v=2r + 3r²sine

Q: A constant force of 512 N was done on an object. If it is known that 1024 Joules of energy was…

A: Given            Force, F = 512 N Work done, W = 1024 J Find   Distance, d

Q: Convert the reading of pressure to kpa. Assuming that borometer reads 760 mm of Hg. (a). 30 cm Hg…

A:

Q: If 15.7 m³ of atmospheric air at 149 degrees centigrade temperature are compressed to a volume of…

A:

Q: Calculate the stress of the cylindrical rod. Compare with data given in Table Q1 which are the…

A: we have to calculate the stress

Q: Compare twin bulb method and diaphragm cell method for determination of diffusivity.

A: Twin bulb method Thermal diffusion can be measured by the two-bulb method. the bulb which is stirred…

Q: 11. Air enters a 10 m long section of a rectangular duct of cross section 25 cm x 16 cm made of…

A:

Q: Knowing that at the instant shown the rod attached at A has an angular velocity of 5 rad/s…

A:

Q: Specific gravity of an oil is 0.8. Find its weight density.

A: The weight density of an oil with a specific gravity of 0.8 must be determined. Given that,  So=0.8,…

Q: A single block brake, as shown, has a tangential braking force of 500 N and normal force 1200 N…

A:

Q: Determine the phase of a substance: Ammonia at 30℃ and specific volume of 0.1 m^3/kg*       a.…

A:

Q: A 50,000 lb box car going 25 mi/h is to be hitched to a gondola carrying bulk copper ore (net weight…

A: following is the solution to the above problem-

Q: Label the following diagram of a fluid dispensing system using the provided labels • Volume Request…

A: Introduction: Fluid dispensing equipments:Fluid dispensing equipment includes any machine that…

Q: Using appropriate sketches, draw a two-stage refrigeration system with a flash chamber. Explain…

A: Two stage refrigeration system means two stage compression refrigeration system.

Q: This landing instrument guides an aircraft to maintain a 2.5 to 3 degrees angle when attempting to…

A: Given question: The landing instrument that guides an aircraft to maintain a 2.5 to 3 degree angle…

Q: The power output of an adiabatic steam turbine is 5 MW, and the inlet conditions are given as P₁ -2…

A:

Q: A centrifugal pump delivers water at a rate of 0.03 m³/sec to a height of 18 meters through a pipe…

A: Given that, Q=30 litres/s=301000 m3/s=0.03 m3/sH=18 m, L=90 mPipe diameter, d=100 mm=0.1 mηo=75…

Q: The product structure diagram shows the number of different components required at each level to…

A: The number of additional units of component A needed to produce 10 units of product P is 110 units.…

Q: Determine the force in members ab,dh,dg, eg, hi,hj, & hk of truss shown in figure !

A:

Q: Give: Otto cycle Compression ratio = 9 Intake air is at 100kpa and 20°C Maximum cylinder volume =…

A:

Q: For propylene plot the residual enthalpy and residual entropy functions over the reduced pressure…

A: Given that, Interpolation formulay-y1=y2-y1x2-x1x-x1y1=0.6       1→Propaney2=0.4…

Q: 3. During the rolling process, the average flow stress is 20,000 lb/in², determining the amount of…

A:

Q: In the figure below, a weight W is suspended from point D of a beam AD. The beam is held up by rod…

A: Consider the above truss carefully. Consider the beam AD, in this it can be seen that there are 3…

Q: A conical spiral spring is submitted to the action of an axial force W. Determine the safe magnitude…

A: A conical spring is known to be subjected to the action of an axial force W. If the number of coils…

Q: A 45° degree strain gauge rosette positioned on the surface of a structure under stress recorded the…

A:

Q: 4***] A string is rolled around a cylinder(   kg) as shown in figure. A person pulls on the…

A: We can use the second equation of motion expression for the acceleration in terms of net.The torque…

Q: Draw shear force and bending moment diagrams for the beam and loading in the figure.

A: Let "C" be the center of the beam. Let the reactions at point A and B are RA and RB respectively.

Q: mass of each cylinder is R, and the radius d secondary force and moment balance.

A: Cylinder 2 fires=270°Mass of each cylinder=RRadius of each mass = r

Q: Choose True or False. a) Consider the truss below that is made up of elements (1) and (2). TRUE or…

A: According to the details provided in the question, we need to calculate the TRUE / FALSE condition.

Q: Draw the simplified free-body diagram and below it the shear and bending moment diagrams. Show all…

A: Draw the free-body diagram of the beam.

Q: 2 Q₂) Find the value and direction of the force applied on an curved blade as shown in the figure…

A:

Q: A Pelton turbine is required to work under a head of 40 m to develop 150 kW at 250 r.p.m. Assuming:…

A: Given that, H=40 m, P=150 kW, N=250 rpm,  Cv=0.98,  Ku=0.46 Mechanical efficiency, ηm=96 %=0.96,…

Q: A 10-inch waterwheel were spinning by the weight of flowing water at one liter per second. If the…

A:

Q: 1- What pull P on the rope must the man exert in order to suspend the 500-Ib crate in the deflected…

A: Given: W=500 lb

Q: F2-13. Determine its coordinate direction angles of the force. F=75 lb

A: We can answer the first question since the exact one is not specified. Please resubmit the question…

Q: Q.1/A Rs) Determine the magnitude of the component force F in Fig. and the magnitude of the…

A:

Q: Convert the reading of pressure to kpa.

A: Given data; Borometer reads =760 mm of Hg Convert 80 cm of Hg into kpa ?

Q: . The cantilever beam is subjected to loading as shown. a) Make section between A and B (0≤x≤1) and…

A: Let moment, M= 20 kNm Let uniform distributed load, w= 8 kN/m Let force, P= 5 kN Length, AB= 1 m…

Q: A plate of 270 mm wide and 25 mm thick from carbon steel. A two-high rolling mill is used to reduce…

A: (a) Calculate the contact length of arc. Lp=R∆H=60025-20=54.77 mm Calculate the true strain.…

Q: Example 18.4: Find the Hori H 20 kN 10 kN. AA 45° 40 kN 60° 30 kN B H

A:

Q: INDUSTRIAL PLANT ENGINEERING Select a proper schedule of pipe for each of the following conditions:…

A: Given Datad=10inP=900psiaT=900F

Q: A house is to be maintained at 20°C when the outside air is at -25°C. It is determined that 1800 kJ…

A:

Q: A glass tube with a 90o bend is open at both ends. It is inserted into a flowing stream of oil (sp.…

A:

Q: 2. A tensile specimen of the metal of 100 mm is length stretched to a length = of 157 mm during the…

A:

Q: The rigid bar DEF is welded at point D to the steel beam AB. For the loading shown, determine (a)…

A:

Q: For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b) determine the…

A:

Q: 3. A 50,000 lb box car going 2.5 mi/h is to be hitched to a gondola carrying bulk copper ore (net…

A: Given: m1 = 50000 lb m2 = 100000 lb v1 = 2.5 mi/hr

Q: Draw shear force and bending moment diagrams for the beam and loading in the figure.

A:

Q: A Carnot engine operates between the temperature limits of 501.85°C and 31.85°C while producing 54 x…

A:

Q: For the following beams, draw the simplified free-body diagram and below it the shear and bending…

A: Given: Let us consider the given image and Calculate the bending moments at the places of zero shear…

Q: v=0 AE- +24V 2 OV 14 3 = K1 2 1Y 1 4 can you please explain how this circuit works 4 5 15$

A: Concept: 1) In the given pneumatic circuit, there is an 3/2 solenoid cum plunger operated…

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.