Using V = 9 mV, and given the voltage across an inductor L = 10 mH as shown in Fig. P6.25, determine the waveform for the inductor current during the time t1 <= t <=t2, where t1 =4 ms and t2-19 ms. Assuming the solution looks like i₁(t) = X(t-t1)² + Y(t-t1) + C, what is the initial condition of the current (the constant, C)? For your answer just put the magnitude of the initial value of the constant and in milliAmps (there should only be a number in your answer). v(t) (mv) V- Figure P6.25 t1 t2 (ms)

Using V = 9 mV, and given the voltage across an inductor L = 10 mH as shown in Fig. P6.25, determine the waveform for the inductor current during the time t1 <= t <=t2, where t1 =4 ms and t2-19 ms. Assuming the solution looks like i₁(t) = X(t-t1)² + Y(t-t1) + C, what is the initial condition of the current (the constant, C)? For your answer just put the magnitude of the initial value of the constant and in milliAmps (there should only be a number in your answer). v(t) (mv) V- Figure P6.25 t1 t2 (ms)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A capacitor is connected to an electrical circuit as shown in the image. The initial voltage of the capacitor will be that obtained when fully charged with all four switches closed. Then the switches that are required for it to start downloading are opened. It is known that after 0.1 s in its discharge process, the voltage on the capacitor is 20% of the voltage it initially had. Questions: 1. Explain how the initial voltage of the capacitor can be calculated.2. Indicate which switches are necessary to start the discharge of the capacitor and why.
6.24.2 In the circuit below, all the capacitors have already reached steady state (no current flowing through the capacitors). Determine the energy (in mJ) stored in capacitor C5, if C₁ = 12 μF, C₂ = 20 μF, C3= 25 μF, C₁ = 23 μF, and C5= 10 μF. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point. 15 mA Your Answer: 10 ΚΩ C₁ C₂ C3 CA C5
The voltage across a capacitor with the value C = 4 F is given by the waveform in Fig.P6.10. Find the waveform for the current in the capacitor for the time interval Os ≤ t≤t2, given that t2 = 15s. PCV) +12 -12 A t1 t2 t3 t4 t(s)
-In the circuit shown on the right the switch S has been open for a long time. What is the current flow through the inductor (0, 2 to 1, or 1 to 2) ? -In the circuit shown on the right the switch S has been open for a long time. At the instant the switch S is closed, the current flow through the inductor is (0, 1 to 2, or 2 to 1)? -In the circuit shown on the right the switch S has been open for a long time. The current flow through the inductor is (increasing, steady, or decreasing)? -In the circuit shown on the right the switch S has been open for a long time. Immediately after the switch S is closed, the current flow through the inductor is (increasing, steady, or deacreasing)? -In the circuit shown on the right the switch S has been closed for a long time. The current flow through the inductor is (1 to 2, 2 to 1, or 0)? -In the circuit shown on the right the switch S has been closed for a long time. At the instant the switch S is opened, the current flow through the inductor is (1…
y. The voltage across the capacitor shown is known to be 2500t up V for tzo - Yc = 500t e 5UF a. Find the current through the capacitor for t >o. b. Find the energy stored in the capacitor at t = 100US
A source-free RC contains an initially charged capacitor with voltage Vo. What is the voltage across this capacitor after a time of t = 17 has elapsed where t is the time constant.
PSPICE The current in a 50 µH inductor is known to be MULTISIM iL = 18te-104 A fort > 0. a. Find the voltage across the inductor fort > 0. (Assume the passive sign convention.) b. Find the power (in microwatts) at the terminals of the inductor when t = 200 ms. c. Is the inductor absorbing or delivering power at 200 ms? d. Find the energy (in microjoules) stored in the inductor at 200 ms. e. Find the maximum energy (in microjoules) stored in the inductor and the time (in milliseconds) when it occurs.
An 8 mH inductor and a 2omega resistor are in series with a 20V battery. The switch is closed for t=0 at which the current is 0. Determine the potential across the inductor and across the resistor.
The charge on a C = 0.4F capacitor is measured as a function of time in a physics lab and produces following graph. The capacitor is part of a simple circuit having only a battery, a capacitor, and a resistor in series. The capacitor starts uncharged and at t=0s, the battery is plugged in and the capacitor charges. In general, the charge of a charging capacitor is given by: q(t) = Qmax(1 – e-t/RC) Charge vs. Time 20 18 16 14 O 12 10 6. 4 2 3 7 8. 10 Time (s) Chart Area Use the graph to estimate the time constant for this circuit, r. Estimate the resistance of the resistor R in this circuit. Charge (C) 00
Please asap
A capacitor is connected to an electrical circuit as shown in the image. The initial voltage of the capacitor will be that obtained when fully charged with all four switches closed. Then the switches that are required for it to start downloading are opened. It is known that after 0.1 s in its discharge process, the voltage on the capacitor is 20% of the voltage it initially had. Questions: 1. Explain how the initial voltage of the capacitor can be calculated.2. Calculate the initial voltage of the capacitor before it begins to discharge.3. Say characteristic switches are necessary to initiate the discharge of the capacitor and why.4. Calculate the value of the capacitance.
Please answer in typing format