Using the indirect addressing method and the DJNZ (Decrement and Jump if Not Zero) instruction, create a loop to transfer the data from addresses 19h to 10h (19h, 18h,...,11h, 10h) to addresses 29h to 20h (29h, 28h......21h, 20h). Note: In order to show that the desired program is working correctly, data must be written to addresses 19h - 10h with a loop.

Using the indirect addressing method and the DJNZ (Decrement and Jump if Not Zero) instruction, create a loop to transfer the data from addresses 19h to 10h (19h, 18h,...,11h, 10h) to addresses 29h to 20h (29h, 28h......21h, 20h). Note: In order to show that the desired program is working correctly, data must be written to addresses 19h - 10h with a loop.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Answer the following questions: 1. Design a 8 bit "shift left-shift right" register. 2. Design a 8 bit up counter. 3. Difference between sequential circuit vs combinational circuit. 4. Design a 8:1 multiplexer using 4:1 multiplexer and 2:1 multiplexer. 5. When designing register file, we used multiplexer to read from a specific register of that register file. However, to write in the register file, we didn't use demultiplexer. Why ? 6. In our designed register file, we can write one data at a time. But if we want to write two data at a time,what should we do ? 7.Logisim simulation: A. Design a 8 bit register file with 10 registers. B. Design an ALU with AND, OR, XOR, NOT, ADD and SUBTRUCT operations that can use the above register file. C. Create a single cycle data-path between register file and ALU. Save 1 digit of your NSU ID in each register of your register file before running instructions given below.E.g. for id: 1831565042, save 1 in first register, 8 in second, 3 in third and…
Write a program to add the following five data bytes stored in memory locations starting from XX60H, and display the sum. (The sum does not generate a carry. Use register pair DE as a memory pointer to transfer a byte from memory into a register.) Make a flow chart for the same. Data(H) 1A, 32, 4F, 12, 27
Parts A ,B , and C. How is -89 represented using 8-bit two's compliment? (The answer should be 8 binary digits) Assume we are using the simple model for floating-point representation as given in the text (the representation uses a 14-bit format, 5 bits for the exponent with a bias of 15, a normalized mantissa of 8 bits, and a single sign bit for the number): Show how the computer would represent the numbers 100.0 using this floating-point format. Express the answer in hexadecimal using 4 hex digits. Suppose we are working with an error-correcting code that will allow all single-bit errors to be corrected for memory words of length 7. We have already calculated that we need 4 check bits, and the length of all code words will be 11. Code words are created according to the Hamming algorithm presented in the text. We now receive the following code word: 01111010101 Assuming even parity, according to our error-correcting code, in what bit is the error? Number the bits from the right…
Solve the following question. You must show your work. a) What does 962F000016 represent in an IEEE single-precision floating-point number? b) Convert -151o to a 16-bit sign-magnitude representation. c) Convert-151o to a 16-bit two's complement representation. d) Define the system status register value after an instruction execution resulted the following: a. Result was a non-zero value, a negative value, had a carry and extended bits. b. Trace mode was not on and was executed in supervisor mode. C. Any higher interrupt priorities higher than level 3 will be recognized.
24. a. The serial adder required six clock pulses to add two, three bit binary numbers. (True or False. Write the correct one, if it's false) b. A three bit parallel adder circuit uses three adders to add all bits on two clock pulse. (True or False. write the correct one, if it's false) c. What is the two's complement of 1001?
con con of son The first 2 pins of the analog pins in Arduino are used to transmit and receive data (TX and RX) O a. False O b. True Which of the following parameters is not a required part in the ARDUINO sketch "for" loop? O a. Initialize O b. Increment OC. Serialprint O d. Condition When an overflow occurred, the C bit in the STATUS register is O a. None of these O b. 0 Oc. Not affected Od 1
the diagram on the right is for a register bank circuit that contain 8 registers. Each register is 16-bit. Theregister can read or write to one register at a time using address bus.Design the circuit and specify the width of EVERY bus.
1.using a shift register to shift a binary one position to the left and adding a zero resultsA. Division of the number by 4B. Multiplication of the number by 2C. Division of the number by 2D. Multiplication of the number by 4 2.using a shift register to shift a binary one position to the right and adding a zero resultsA.Division of the number by 2B.Division of the number by 4C.Multiplication of the number by 4D.Multiplication of the number by 2
Write a program in assembly language to toggle PORTB 400 times. Use BNZ instruction.
Procedure: 1. Design an even/odd parity generator for 4-bit data. 2. Design a parity checker circuit for a 4-bit data. 3. Design a logic circuit for a 3-bit message to be transmitted with an even parity bit. 4. Four data bits are to be transmitted. Design a parity bit generator to give an o/p of 'l' if the number of logic l's in the message is: (i) odd; (ii) even.
Show the starting and ending address of each segment located by the following segment register values. 1. 56F8H 2. C802H 3. 7FFEH 4. 7103H 5. 1110
SV What is clocking block ? what is program block?