Answered: Use the approximate method to estimate…

Use the approximate method to estimate the stress (kPa) under the center of a rectangular loaded area 2 m X 3 m at a depth of 2 m, if the .vertical load is 20 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A concentrated load of 2000 kN is applied at the ground surface. Determine the vertical stress at a…

A: Solution Given Data Concentrated load= 2000 kN

Q: If the gauge of the railroad shown on the plan above is 1.7 m and produces a line-like loading at…

Q: 50 and 100 kN/m vertical line loads are applied on the ground surface as shown in the figure.…

A: For, load= 50 kN/m vertical stress = (2Q/Z) (1/[1+(x/z)])2 Q= 50kN/m x= 5m, Z = 30m Therefore,…

Q: Practice Problem: Refer to Figure 3.70, a flexible square area is subjected to a uniformly…

A: Given: The distributed load (q) is 100 kN/m2. The depth is 4 m. Consider the figure,

Q: A 3m by 4m rectangular area carrying a uniform load of 240 kPa is applied to the ground surfae.…

Q: A uniformly distributed line load of 500 kN/m is acting on the ground surface. Based on Boussinesq's…

A: Given data- Line load UDL=500 kN/mdepths-z1=2 mz2=4 mTo Find-Ratio of vertical stresses at 2 m and 4…

Q: Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure P6.2).…

A: Applying Boussinesq's Equation: ∆σz=3P2πz21+rz25/2 ...(1)

Q: If the gauge of the railroad shown on the plan above is 1.7 m and produces a line-like loading at…

A: Data given;Gauge of railroad= 1.7mdistance (Y) = 1.9mDepth = 0.5mFormula used:I=1π(2×θ+sin2θ)

Q: A square foundation of (5m x 5m) is to carry a load of 4000KN.calculate the vertical stress at a…

Q: A rectangular footing as shown in the figure below (shaded area) exerts a uniform pressure of 500…

A: Given- P=500KN/m2d=2m

Q: A uniformly distributed line load is acting on the ground surface. Based on the Boussinesq's theory,…

Q: 2. A rectangular loaded area ABCD shown in figure below carries a load of 80kN/m? Using Fadum chart…

A: Draw:

Q: 10-16. A 1 m cube within a mass of stressed soil has a stress of 100 kPa on its top and bottom…

A: since the given question is having multi sub parts therefore as per guidelines only 1-3 subparts…

Q: A concentrated load of 1800 kN is applied on the surface of the ground. By using Boussinesq…

Q: A rectangular raft of size 26 x 10 m founded on the ground surface is subjected to a uniform…

A: Given Data: The total length of the raft is L=26 m. The total width of the raft is B=10 m. The…

Q: A strip load of q=810 lb/ft2 is applied over a width B=36ft. Determine the increase in vertical…

A: given data;- q=810 lb/ft2 b=36 ft z=15 ft x=27 ft

Q: Compute the vertical stress increment

Q: A point load of 700 kN is applied on the surface of thick layer of saturated clay. Using…

Q: Point loads of magnitude 100,200,and 400kN act at B, C, and D, respectively. Determine the increase…

A: Given :

Q: A rectangular foundation 4 m x 6 m transmits stress of 300 kPa on the surface of a soil deposit, as…

A: r=4m z=5m

Q: B 6.0 m 6.p m 5.0 m Figure for Problem6

Q: 10.17 Refer to Figure 10.47. A flexible rectangular area is subjected to a uniformly distributed…

A: Given :

Q: Use Eq. (6.14) to determine the stress increase Δσ at z = 10 ft below the center of the area…

A: Solution; Calculate parameter m1 as follows: m1=LBHere,The width of the foundation =B=10 ftLength of…

Q: 2- Point loads of magnitude 100, 200, 300 and 400 lbs. act at A, B, C, and D, respectively.…

A: Given Data: The point loads A, B, C and D are given as: QA = 100 lbsQB = 200 lbsQC = 300 lbsQD = 400…

Q: SITUATION: Refer to Figure below. Point loads of magnitude 500 KN, 750 KN, 800 KN, and 1000 KN act…

Q: An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The…

A: Given data: Q=33 kN Z= 2 m From the base of the pole. r=0. At the center of the pole.

Q: A concentrated load of 1000 kN is applied at the ground surface. Compute the vertical stress at a…

A: Given data : The value of concentrated load Q=1000 KN The value of depth Z=4 m The value of radial…

Q: A point load of 700 kN is applied on the surface of thick layer of saturated clay. Using…

Q: Н.О 4 Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure below).…

A: The given data is: Load at point B (QB) = 100 kN Load at point C (QC) = 200 kN Load at point D (QD)…

Q: (b) Figure Q2 (b) shows the ring foundation to support a silo. Given R1 = 3 m while R2 = 6 m. The…

A: Given data: R1= 3 mR2=6 m Depth 7 m with a interval of 1m.

Q: Point loads of magnitude 9, 18, and 27 kN act at A, B, and C, respectively (Figure 6.27). Determine…

Q: Refer to Figure 10.47. A flexible rectangular area is subjected to a uniformly distributed load of q…

A: Given data, q = 330 kN/m2 z = 6 m L = 18 m B = 9 m Influence values are obtained from the given…

Q: A uniformly distributed line load of 500 kN/m is acting on the ground surface based on Boussinesq's…

A: Given data: A uniformly distributed line load of 500 kN/m. The ratio of vertical stress at a depth 2…

Q: 100 kN point load and 40 kN/m line load are applied on the ground surface as shown. Compute the…

Q: 10.7 Point loads of magnitude 125, 250, and 500 kN act at B, C, and D, respectively (Figure 10.40).…

A: To find out the increase of vertical stress at a depth of 10 m below the point of A.

Q: Ex2: An embankment shown in the figure is constructed. compute the vertical stress increment under…

Q: b) An electric pole is held vertically by three equally spaced wires tied at the top of the pole.…

A: Introduction : According to Boussineq's point load theory : Vertical stress : σz =…

Q: Calculate the added vertical stress at points A and B as deep as Z = 8 m, under the rectangular load

Q: Figure below shows an embankment load on a silty clay soil layer. Determine the stress increase at…

Q: Consider a circularly loaded flexible area on the ground surface. Given that the radius of the…

A: This problem is related to vertical stress topic from Soil Mechanics. In this problem there are…

Q: Determine the vertical stress increase 6 m below point E.

Q: The plan of a flexible rectangular loaded area is shown in Figure 6.30. The uniformly distributed…

A: Solution: The equation for determining the increase in stress on a flexible rectangular area at a…

Q: B q = Load per unit area

Q: A single rectangular opening 10 ft (3.0 m) in height is driven in rock having strengths of fc =…

A: Given Data: Opening height is Ho=10 ft. Strength of rock in compression is fc=18000 lb/in2. fc=18000…

Q: Compute the increase in the stress at point A when two line loads of value 90 kN/m and 325 kN/m act…

A: Given: Line load 1, q1 = 90 kN/m Line load 2, q2 = 325 kN/m x1 = 4 m x2 = 2.5 m z = 3 m

Q: Find the vertical stress increment at the depth of 5m below the centre and corner of the loaded…

A: The increment in stress will be due to applied load

Q: CEN-333 Geotechnical

A: Boussinqi's equation: σZ=QZr32π11+rZ252where,Z=Depth of the pointQ=point load actingr=radial…

Q: The plan of a flexible rectangular loaded area is shown in Figure below. The uniformly distributed…

Q: Refer to the figure below. Ao,, at point A with the following values: q1 = 120 kN/m; q2 =350 kN/m;…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

i need the answer quickly

Use the approximate method to
estimate the stress (kPa) under the
center of a rectangular loaded area 2
m X 3 m at a depth of 2 m, if the
.vertical load is 20 kN
2 O
1 O
1.67 O

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A hollow circular tube is subjected to a tension force of 30 KN, a tensile stress of 20 MPa was recorded.lf the outer diameter of the tube is 100 mm, the inner diameter will be eqaual to. a. 93.95 mm O b. 89.95 mm C. 85.95 mm o d. 91.95 mm
6O cm 20 20. 20cm 20 cm CrOSS - section 1. Determine the value the max Yalue g mament is 702 kN. cm gbending Stress of 2. Determine the ralue sf shean SKess of the max value g shean is 420 KN -
b) A rectangular block of 1200 mm² cross-sectional area is subjected to a longitudinal compressive load of 1200kN. Determine the normal stress across the cross section of the block. If the block is cut by an oblique plane making an angle of 400 with normal section of the block. Determine: (i) Normal stress on the oblique plane (ii) Tangential stress along the oblique plane, and (iii) Resultant stress on the oblique plane.
10-16. A 1 m cube within a mass of stressed soil has a stress of 100 kPa on its top and bottom faces, 50 kPa on one pair of vertical faces, and 30 kPa on the other pair of vertical faces. There is no shear stress on any face. Fill in the numerical values for each stress and angle in the following table. (After Taylor, 1948.) o(kPa) 7(kPa) a Major principal plane: Intermediate principal plane: Minor principal plane: Plane of maximum shearing stress: Plane of maximum obliquity: Note: a is with respect to the horizontal plane.
A 2.4 diameter steel molding is lifted by 4 steel cables as shown. The mold weighs 3 kN/m. (a) what is the required diameter of wire that will not exceed the allowable stress of 120 MPa. and (b) if the wire diameter increase by 20%, find the vertical displacement of the molding.
What is the value of the shear stress at the neutral axis in a rectangular section of base b, height h and subjected to the shear force F? 1.3F/b O 2. (3F)/(2bh) O 3. F/2
Sketch the normal stress distribution acting over the cross section at section a-a. 6 kip 12 kip 3 in.
A piece of engineering equipment is supported by thefoundation shown. The diameter of the circular pin is 20 mm. a.) Determine the value of P so as not to exceed the allowable bearing stress of 310.5 Mpa in the circular pin.b.) Determine the value of P so as not to exceed the allowable shearing stress of 138 Mpa in the circular pin.
Numerical Analysis (HW. #1) The vertical stress increment (Ao) due to a point load acting on the surface of linearly elastic medium is given as: 3P23 Ao 27Vr? + z? where P is the magnitude of the load, r is the lateral distance, and z is the depth of the point where the stress is to be calculated. If P = 10g kN and r = using two methods: fixed-point and Newton-Raphson method) the depth z at which the stress increment Ao = 10n kN/m?. (Take g=student group number A=1, B=2, 1.5 m, determine (by C=3, D=4, and E=5, n=student number in his/her group, and & =1x10-6)
Determine the strain energy by considering effect of the normal stresses. E=200GPa 80 kN 80 kN W310 X 74 E I 4.8 m Need neat and clean handwritten solution explaining every steps A D 1.6 m-1.6 m-1.6 m- B
A distributed load of w N/m is applied over an entire length of a simply supported beam 8m long. The beam section is made up of four 20mmx100mm rectangles arranged as shown. A. Determine the maximum value of w without exceeding the permissible flexure stress of 10MPa. B. Determine the maximum value of w without exceeding the permissible shear stress of 1.2MPa. C. Determine the maximum value of w without exceeding the permissible screw strength of 800N for a pitch of 75mm.
The beam shown has a rectangular cross section with a depth h = 240 mm. Determine the width b of the section if the material has ultimate normal stress of 100 MPa and the safety factor is F.S 1.8. 60 kN/m 70 kN-m 2 m 2 m A B C