urrent Attempt in Progress A Spring Gun. A hydraulic press is used to compress a spring that will then be used to project a 23.0-kg steel ball. The system is similar, but smaller in scale, to the car jack illustrated in Figure 11.14. In this case, the smaller cylinder has a diameter of d₁=0.85 cm and has a manually operated plunger. The larger cylinder has a diameter of d2 - 12.0 cm, and its piston compresses the spring. The idea is that the gun operator pulls a lever that pushes the plunger on the small cylinder, which transmits a pressure to the larger piston that, in turn, exerts a force on the spring and compresses it. Once the spring is compressed, the steel ball is loaded and the spring is released, ejecting the ball (a) If a force of 1000 N is exerted on the primary (smaller) piston to compress the spring 1.00 m from its equilibrium (uncompressed) position, what is the spring constant k of the spring? (b) What is the velocity of the steel ball just after it is ejected? (c) Neglecting air resistance, what is the maximum range of this "spring gun"? (a) Number Units

urrent Attempt in Progress A Spring Gun. A hydraulic press is used to compress a spring that will then be used to project a 23.0-kg steel ball. The system is similar, but smaller in scale, to the car jack illustrated in Figure 11.14. In this case, the smaller cylinder has a diameter of d₁=0.85 cm and has a manually operated plunger. The larger cylinder has a diameter of d2 - 12.0 cm, and its piston compresses the spring. The idea is that the gun operator pulls a lever that pushes the plunger on the small cylinder, which transmits a pressure to the larger piston that, in turn, exerts a force on the spring and compresses it. Once the spring is compressed, the steel ball is loaded and the spring is released, ejecting the ball (a) If a force of 1000 N is exerted on the primary (smaller) piston to compress the spring 1.00 m from its equilibrium (uncompressed) position, what is the spring constant k of the spring? (b) What is the velocity of the steel ball just after it is ejected? (c) Neglecting air resistance, what is the maximum range of this "spring gun"? (a) Number Units

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Asap plzzx
Water gauge pressure available at a fire hydrant is 80 psi. If a fire hose is connected to the hydrant and the hydrant valve opened, how high can the end of the hose be raised and still have water flowing out? ASsume that no nozzle is attached to the end of the hose. a. 826.94 m b. 91.2 m c. 56.25 m d. 8.16 m
Pressure cookers have been around for more than 300 years, although their use has strongly declined in recent years (early models had a nasty habit of exploding). How much force must the latches holding the lid onto a pressure cooker be able to withstand if the circular lid is 25.0 cm in diameter and the gauge pressure inside is 300 atm? Neglectn the weight of the lid.
لابد B A These four containers are filled with the same volume of water. Which has the highest pressure at the bottom? A B C
Which of these has maximum torque? The angle between the applied force and moment arm is 30 degrees The force and the moment arm are perpendicular The force applied directed on the pivot point O The force and the moment arm are parallel input force is used to exert a large output force by making the area of the output piston larger than the area of the input piston. O Zero O Wide O Large O Small
Calculate the Reynolds number for an object moving through a fluid.
can you please help me here? and also, put the answer as decimals or whole number. thank you.
2. Set the parameters of the simulation as below. D = pipe diameter P = pressure u = fluid velocity Din = 5.0 cm Pin = 107 kPa Uin 3. = 3.8 m/s Az = 7.4 m Dout = 6.4 cm = 39 kPa out = 2.3 m/s u out Directions Change in height Outlet pipe diameter Inlet pressure Inlet velocity Details Display: Fluid properties Energy About 7.4 m 6.4 cm 107 kPa 3.8 m/s density p = 1000 kg/m³ and g = 9.8m/s^2 Using the simulation, verify using Bernoulli's equation if the outlet velocity and outlet pressure value in the simulation is correct?
The piston of the hydraulic cylinder gives pin A a the instant when 0 = 54°, determiner, 7, 9, and 6.1" Answers: r = = ö = -1.2343 i -1.6988 2.7039 10.623 ft/sec constant velocity v = 2.1 ft/sec in the direction shown for an interval of its motion. For where r = OA. ft/sec² rad/sec rad/sec²
Please asap
Oil (p = 920 kg/m³) is flowing through a pipeline at a speed of 1.88 m/s. If the diameter of the pipe is 0.16 m, what is the %3D mass flow rate? kg/s
9.8