UPVOTE WILL BE GIVEN. Please write the complete solutions and box the final answer. Use 4 decimal places. Fundamentals of Surveying When the temperature was 30°C, the distance from A to B was laid out using a steel tape that has a standard length of 20°C with coefficient of thermal expansion of 0.0000116/°C. If the correct distance from A to B is 584.5m, what is the measured distance in m?

Q: The following data were obtained by stadia measurement. If the height of the instrument is 1.362m…

A: K=96.8m C=0.3m S1=2.216m S2=1.06m

Q: The instrument was set at point E and the rod readings at points E and F are taken as 3.226 meters…

A: observations are as followsstationstaff reading at point Estaff reading at point…

Q: PROBLEM NO.04. The length of a line was measured repeatedly on three different occasions and…

A: To find weighted mean

Q: Problem 5 Angles AOB, BOC, and COD are measured on the same angle at point O. Determine the most…

A: GIVEN : Measurement of Angles, number of measurements. REQUIRED : Most probable Angle, MPV

Q: A steel tape, with a coefficient of linear expansion of 0.0000116/C, is known to be 50 meters long…

A:

Q: The following values were determined in a series of tape measurements of a line: 1000.58, 1000.40,…

A: We will use the standard formula to calculate the standard deviation.

Q: A circular water tank with a diameter of 10 m and with uniform cross section , some angles…

A: Diameter of circular tank = 10m MB is at the center of bottom base. Zenith angle = 1400

Q: Consider the cylindrical buoy pictured below floating in sea water with density p= 1025 kg/m³. The…

A: A rectangular cuboid is given H =1715mm = 1.715 mD = 1.127 mM = 744 kgDensity of sea water = 1025…

Q: A distance of 1500 m was measured with a 20 m chain. After the measurement chain was found to be 60…

A:

Q: b) Determine the measured the Correction due to Pull for line

A: Given, Pull applied, Pa= 75kg Standard pull, Ps= 50 kg Area, A= 6.50 mm2 Modulus of Elasticity, E=…

Q: A 100-m tape that is "x" m. too long was used to measure two points and the result is 420.307m. It…

A: True length of tape,TL =(100+x) mNominal length of tape, NL = 100 mMeasured distance between two…

Q: For a vector, F = 86.02 kN at an angle of %3D 50.11 degrees made with the horizontal in Q4. Find the…

A: To Find :- Vertical component of a Force vector

Q: D. (Round off to 3 decimal places) An angle was measured with different weights as follows:…

A: Hi! Thank you for the question, as per the honor code, we are allowed to answer three sub-parts at a…

Q: The correct distance between points C and D is 213.5m. If a 100-m tape that is 0.025m too long is…

A:

Q: ERBsent out six groups of students to measure a distance between two points on the ground. The…

A: The measured value of the distance between the two station -  X1 = 360.52m X2 = 360.35m X3 = 360.89m…

Q: Datum in the figure, A. Ar elev, eleve and the measured slope length L were 1.634, 1.546, 987.207,…

A: he =1.634 mhr = 1.546 mElevA = 987.207 mElevB = 1006.816 mL = 435.955 m

Q: Given are the interior angles of a heptagon. Determine the discrepancy for the givenobservation and…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: Plugging when performing the longitudinal section leveling of a road, the readings were recorded…

A: We know that, HI=BM+BSRL=HI-ISRL=HI-FS Here BM is the bench mark, HI is the height of instrument, RL…

Q: using the method in analysis of beam deflections and rotations (CONJUGATE BEAM METHOD), find the ff.…

A: Given, Young modulus E is 80 GPa Moment of inertia I is 100×106 mm6

Q: 5. For several measurements of a required distance, the most probable value is 546.75 m. If +/-0.15…

A:

Q: A line was determined to be 2,651.56 meters when measured with a 30 m. steel tape supported…

A:

Q: In the figure shown, theodolite is being set up at point "A" and "C", and subtense bar at point "B".…

A: Given data: Horizontal angel AB= 3.5o Horizontal angel CB= 1.5o HI of all the stations = 1.5 m

Q: A rock is thrown horizontally froma tower at A and hits the ground 5.0 s later at B. The line of…

A: apply equation of motion

Q: A distance of 17.44 m is measured with a tape. During measurement, the other end was discovered to…

A:

Q: 2. An archaeologist took some measurements on the unique mountain he had found. He sets two points X…

A:

Q: The measured distance from A to B was 300.0m. The tape used has a standard length of 30m, at 20 °C…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: a. Two points A and B (distance =100m) were nominated at the field and Two points A and B (distance…

A: The staff readings at point A and point B are given in the above table.The leveling instrument is…

Q: 27. Record the level rod readings to the nearest two decimal places. 1. 2. 3. 2. 3.

A:

Q: Problem 1: If the elevation of point A is 9.722m, elevation of point B= 30.194m, slope distance is…

A:

Q: A line was determined to be 2,682.13 meters when measured with a 20 m. steel tape supported…

A:

Q: 5) Calculate the horizontal displacement of B and the vertical displacement of D. 5m B 21 -4 m- I 1…

A:

Q: 1. Measure and record the distance AC = 6.15. 2. Measure angle ACB = 56 °16'0.79" 3. Find the…

A: This type of surveying is carried out when there is obstruction between two point and difficult to…

Q: a. What difference in temperature from standard if neglect in use of a steel tape will cause an…

A: Answer  To calculate the difference in temperature from standard based on the given data, we can use…

Q: For a vector, F = 169.35 kN at an angle of 88.46 degrees made with the vertical in Q2. Find the…

A:

Q: D. (Round off to 3 decimal places) An angle was measured with different weights as follows:…

A: Note : Since you have posted a question with multiple sub-parts, we will solve the first three…

Temperature Difference and Heat Transfer

Whenever there is a flow of heat flux resulting from a temperature gradient within the material or between two materials, there is heat transfer. Heat transfer primarily arises due to temperature differences between two bodies or within bodies. The term temperature gradient denotes temperature differences or variation of temperature due to change in some quantity. The fundamental use of the concept of temperature is found in the zeroth law of thermodynamics.