Unless otherwise stated, take the density of water to be P. = 1000 kg/m' and its specific weight to be Y. = 62.4 lb/ft'. Also, assume all pressures are gage pressures unless stated otherwise. 2-125. The container of water has a mass of 20 kg. Block B has a density of 7840 kg/m² and a mass of 30 kg. Determine the total compression or elongation of each spring when the block is fully submerged in the water. kc = 5 kN/m B D. kp =2 kN/m

Unless otherwise stated, take the density of water to be P. = 1000 kg/m' and its specific weight to be Y. = 62.4 lb/ft'. Also, assume all pressures are gage pressures unless stated otherwise. 2-125. The container of water has a mass of 20 kg. Block B has a density of 7840 kg/m² and a mass of 30 kg. Determine the total compression or elongation of each spring when the block is fully submerged in the water. kc = 5 kN/m B D. kp =2 kN/m

Name: Unless otherwise stated, take the density of water tobe P, = 1000 kg/
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Unless otherwise stated, take the density of water tobe P, = 1000 kg/m³ and its specific weight to beY, = 62.4 lb/ft'. Also, assume all pressures are gage pressuresunless stated otherwise.2-125. The container of water has a mass of 20 kg. Block Bhas

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 2000 kg concrete pipe has a center of mass at point G. If it is suspended from cables AB and AC. The diameters of AB and AC are 12 mm and 10 mm, respectively. Determine the weight of the concrete pipe ( in N).
A cargo truck with a weight of 289kN was raised using a hydraulic press. If oil acts on piston with 473mm diameter. Determine the pressure in kPa under the piston.
The brake system in most cars makes use of a hydraulic system. This system consists of a fluid filled tube connected at each end to a piston. Assume that the piston attached to the brake pedal has a cross sectional area of 0.6 cm2 and the piston attached to the brake pad has a cross section area of 2.4 cm2. Determine the force at the brake pad, if you apply a force of 10 N to the piston attached to the brake pedal. Please show the formulae, the calculations, all the steps.
side the cylinder. (123.35kPa) Both a gage and a manometer are attached to a gas tank to measure its pressure. If the reading on the gage is 80kPa, determine the distance between the two fluid levels of the manometer 1.9 if the fluid is (a) mercury (p-13600kg/m') or is (b) water (p=1000kg/m). 1 10 The level of the water in an enelosed water
Given the two compartment vessel as shown in the figure. Gage A reads 85 psig, gage B inside the compartment X reads 25 psig. If the barometer reads 30.61 in Hg, determine the reading of gage C. Q P6=25 sig P =? P= 85 psig
The Centre of the pressure of a plane surface is immersed in a liquid equal to the weight of the liquid displaced by the body and acts horizontally upward. Select one: O True O False
The tank shown is filled with water to a depth of d=6 m. Determine the resultant force the water exerts on side A of the tank if the density of water is 1000 kg/m³. Sides A and B face the viewer. 4 m 3 m A B d 706.3 kN 698.2 kN 763.1 kN 582.4 kN O 389.2 kN
What is the hydrostatic force (kN) that acts on the Gate A-B? Given that the specific gravity of liquid S=8.0. 1 m Depth of Gate A-B is 6 m 4 m Liquid 30 DI
A simple U tube manometer is used to measure the pressure of oil flowing in a pipeline. Its left limb is open to the atmosphere and the right limb is connected to the pipe. The center of the pipe is 52 mm below the level of mercury in the left limb. If the difference of mercury level in the two limbs is 131 mm, determine the gauge pressure of the oil in the pipe in Pascal. The specific gravity of the oil & mercury is 0.74 and 13.6 respectively. Solution: (1) Density of oil in kg/m3 (ii) Density of mercury in kg/m3 (iii) Height of the Oil in the right limb (in meters of oil) h1 (iv) The gauge pressure of the oil in the pipe in (in Pascal)
A dam on a river is built so that the wall facing the water is shaped like the region above the curve y = 0.52 and below the line y = 280. (Here, distances are measured in meters.) The water level is 40 meters below the top of the dam. Find the force (in Newtons) exerted on the dam by water pressure. kg m³ (Water has a density of 1000- and the acceleration of gravity is 9.8- m sec² L 80 SHE GRADE
Determine the force on hinge C and block D if the gate holding the water is 6 meters wide into the page.
The concrete gravity dam is held in place by its own weight. If the density of concrete is 2.5 Mg/m3, and water has a density of 1.0 Mg/m³, determine the magnitude of the total resultant force the water exerts on the dam. The width of the dam is 10 m, and d=3 m. F m- 6 m -d – 1–| 1861 kN 1789 kN 1776 kN 1941 kN 1960 kN