Unfortunately, as soon as the button is released, the LED turns off and will not come back on when the button is pressed again. Your classmate's psuedocode is pasted below. Explain what the classmate needs to do to make this program work correctly and rewite their pseudocode. Pseudocode program Declare Pino as an output Declare Pin1 as an input WHILE Pin1 is HIGH Set Pin0 HIGH Pause for 0.5 seconds Set Pino LOW Pause for 0.5 seconds ENDWHILE

Unfortunately, as soon as the button is released, the LED turns off and will not come back on when the button is pressed again. Your classmate's psuedocode is pasted below. Explain what the classmate needs to do to make this program work correctly and rewite their pseudocode. Pseudocode program Declare Pino as an output Declare Pin1 as an input WHILE Pin1 is HIGH Set Pin0 HIGH Pause for 0.5 seconds Set Pino LOW Pause for 0.5 seconds ENDWHILE

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Graphical Representation of the signal 1) Write the type of the voltage from simulation results: 2) Write the value of the voltage from simulation result: L....... -2 DDU 12ns SónG Trace Color Trace Name X Values CURSOR 1,2 V(R1:1,0) Y1 Y2 Y1 - Y2 5.0373m 0.000 5.0373m 249.983 0.000 249.983 Y1(Cursor1) - Y2(Cursor2) Y1-Y1(Cursor1) Y2 - Y2(Cursor2) Max Y Min Y Avg Y 249.983 0.000 0.000 249.983 0.000 124.991
The p-channel JFET used in Digital technology as_____. a.switch b.rectifier c.invertor d.amplifier
RESEARCH What is an INTEGRATED CIRCUIT (IC)? Uses or applications of Integrated Circuit. Types of Integrated Circuit. Draw at least 4 typrs of IC. Discuss the different IC packages. How to identify the pin numbering of IC? Proper handling of IC. What is seven-segment display? How to produce the required decimal digit from 0 through 9 using seven-segment display? Uses of seven-segment display.
Demostrate obtaining 8 to 1 using 2 to 1 multiplexer using the IC 74157 IC. How the connection will be done?
I have four ESP-WROOM-32D boards, and four NRF24L01 modules. Each ESP-WROOM-32D board is connected to one NRF24L01 module. I want one NRF24L01 module to send a "Hello" message to the other three NRF24L01 modules at the same time. What is a good starter code in Arduino IDE?
Advantages and disadvantages of DIGIT IC
QUESTION 1 ------- OUT AN 2 f-4 pleser Tristate CLK Fir-lop hufler clock Observe the OLMC and programmed circuit. Complete the output waveform Note the clock, if you would use it, is positive edge triggered. clock A.
Give the meaning of each acronym of solid state devices. Also sketch the schematic symbol for each device. SUS Shockley diode D-MOSFET JFET SCR DIAC THYRISTOR Device TRIAC 1. 3. 4. 6. 8. 10. 12. 14. Symbol 2. 5. 7. 9. 11. 13. 15. Meaning No entry
Arrange the chronological order of the elements and its function to Digital Communication by writing the numbers 1 to 10 in both column A and column B. A Elements Channel Decoder Channel Encoder Digital Demodulator LICHTE SE Digital Modulator Input Transducer Channel Output Signal Output Transducer Source Source Decoder Source Encoder B A ndeseng Function After detecting the sequence, it does some error corrections. A It can be an analog signal. It compresses the data into minimum number of bits. It converts the signal into the original physical form, which was at the input of the transmitter. It does the coding for error correction. It allows the analog signal to transmit from the transmitter end to the receiver end. It produced after the whole process. It takes a physical input and converts it to an electrical signal. The received signal is demodulated as well as converted again from analog to digital.notni erli lo ini arli lo voeber edirsin.sm The resultant signal is once again…
Draw a 2x1 multiplexer block diagram.Create the status table. Find the simplest form of circuit output with Karnaugh.Explain the circuit problem that may occur.What should be done to fix the problem?(NEED A NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE)
Do calculation. This is not a simulation problem
onal clock cycles form one bus cycle. ROM can be classified into Dynamic ROM and Static ROM. Select one: O True O False Auxillary carry flag will be set whenever O a. there is a carry from lower nibble to higher nibble as well as borrow from higher nibble to lower nibble O b. there is a carry from higher nibble to lower nibble Wingos there is a borrow from lower nibble to higher nibble C. OlacVl Jal none of the choices are correct