UJT, it turns off when the voltage at the emitter reaches a. turn off voltage, b valley voltage, c. a negative voltage, d. peak voltage 3. resistive control gate circuits have a limitation on the maximum firing delay angle. What can be done to increase the firing delay? a. adding a capacitor, b. using a UJT, c. adding a diode, d. all og the above. 4. it is a three terminal breakover type of device that will turn on when the peak voltage at the emitter is achieved a. BJT, b. UJT, c. FET, d. SCR 5. The turn on voltage if a UJT is dependent on a. external resistors, b. instrinstic standoff voltage, c. supply voltage, d. intrinsic standoff voltage and

UJT, it turns off when the voltage at the emitter reaches a. turn off voltage, b valley voltage, c. a negative voltage, d. peak voltage 3. resistive control gate circuits have a limitation on the maximum firing delay angle. What can be done to increase the firing delay? a. adding a capacitor, b. using a UJT, c. adding a diode, d. all og the above. 4. it is a three terminal breakover type of device that will turn on when the peak voltage at the emitter is achieved a. BJT, b. UJT, c. FET, d. SCR 5. The turn on voltage if a UJT is dependent on a. external resistors, b. instrinstic standoff voltage, c. supply voltage, d. intrinsic standoff voltage and

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
1. A six-pulse uncontrolled recti load. The inductance is very 1 (a) Determine average load o (b) Determine the maximum (c) Determine the maximum (d) Determine average loac (e) Carefully sketch the wav diode conduction pattern.
Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage VPP=20 V and bias voltage VBias= 2.7 v. a) What is the function of the circuit? b) Draw the circuit diagram. c) Draw the input and output waveforms.
A. Draw the circuit diagram of a simple positive clamper with input and output waveforms (with values) for an input peak to peak of Vpp = 20 Volts Assume Germanium diode is used. 7
Negative Peak Clipper with bias circuit uses a germanium diode, with an input peak to peak voltage V=20 V and bias voltage V 2.7 v. a) What is the function of the circuit b) Draw the circuit diagram. c) Draw the input and output waveforms. Input Output
ww. ETC CIMS Draw the output waveform for the given circuit diagram with proper values and also mention the name of the circuit. The input waveform Vi is having a peak-to-peak value of 15 V and the bias voltage is 3 V. Assume diode to be silicon. Vi Vo Maximum value of output waveform Minimum voltage of output waveform Finish
The PIV for each diode in a full-wave center- tapped rectifier is............. Note: Vp(out) = peak output voltage. Choose correct answer : A) Vp(out) + 0.7 V B) Vp(out) – 0.7 V C) 2Vp(out) + 0.7 V D) 2Vp(out) – 0.7 V
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) (b) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
Draw the output waveform for the given circuit diagram with proper values and also mention the name of the circuit. The input waveform Vi is having a peak-to-peak value of 13 V and the bias voltage is 4 V. Assume diode to be silicon. Vo Maximum value of output waveform Minimum voltage of output waveform www.
Determine the range of Vi to maintain the Zener diodes in the ON state
b. Calculate the following about the circuit in the figure (If silicon diodes are employed in the rectification);i. the peak value of the output voltage considering the drop across each diode, Vpk.ii. the average voltage, Vdc. iii. The current through the load resistor, IL.iv. The current diode, Id.v. The frequency of the output signal, Fout.vi. Calculate the efficiency of the full wave rectifier expressed in percentage. vii. Sketch a graph of the input and output voltage against time.
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). (b) Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).