Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12 in. A concentrated load of 60 lbf is then applied vertically downwards at a point 4 in. from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E = 29,000 ksi. %3D

Two vertical steel wires each 0.05 in. diameter and 48in. long support a light rod over a span of 12 in. A concentrated load of 60 lbf is then applied vertically downwards at a point 4 in. from one of the wires. Determine the load, stress and extension on each wire and the angular displacement of the rod from the horizontal assuming it does not bend. Use E = 29,000 ksi. %3D

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.6.9P: A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape...

See similar textbooks

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
An aluminum bar has length L = 6 ft and diameter d = 1.375 in. The stress-strain curse for the aluminum is shown in Fig. 1.34. The initial straight, line part of the curve has a slope (modulus of elasticity) of 10.6 × 106 psi. The bar is loaded by tensile forces P = 44.6 k and then unloaded. (a) That is the permanent set of the bar? (b) If the bar is reloaded. what is the proportional limit? hint: Use the concepts illustrated in Figs. l.39b and 1.40.
The strength-to-weight ratio of a structural material is defined as its load-carrying capacity divided by its weight. For materials in tension, use a characteristic tensile stress obtained from a stress-strain curve as a measure of strength. For instance, either the yield stress or the ultimate stress could be used, depending upon the particular application. Thus, the strength-to-weight ratio RS/Wfor a material in tension is defined as Rs/w= in which a is the characteristic stress and 7 is the weight density. Note that the ratio has units of length. Using the ultimate stress Uas the strength parameter, calculate the strength-to-weight ratio (in units of meters) for each of the following materials: aluminum alloy 606I-T6, Douglas fir (in bending}, nylon. structural steel ASTM-A57.2, and a titanium alloy. Obtain the material properties from Tables [-1 and 1-3 of Appendix I. When a range of values is given in a table, use the average value.
A steel column (E = 30 x 103 ksi) with pinned ends is constructed of a W10 x 60 wide-flange shape (sec figure). The column is 24 ft long. The resultant of the axial loads acting on the column is a force P acting with an eccentricity n = 2.0 in. If P = 120 kips, determine the maximum compressive stress ff^ in the column. Determine the allowable load Pallowif the yield stress is ( y =42 ksi and the factor of safety with respect to yielding of the material is n = 2.5.
3) A 10 kN-m torque, T, and a 50 kN axial load, F, are applied to the end of an aluminum 6063 tank containing compressed air under a pressure of 2 MPa. The tank has a 400 mm outer diameter and a 20 mm wall thickness. Aluminum 6063 has a yield strength of 48 MPa. a. Draw and label a stress element for the most stressed point on the tank. Explain why this is the most stressed point. b. Sketch Mohr's circle and find the principal stresses at the most stressed point. Make sure you label your axes! c. Determine whether or not this is a safe loading scenario by considering the max normal stress, max shear stress, and distortion energy. (Hint - calculate the factor of safety for each failure criteria) T
Let's considera rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F Select one: OF 5236 N O F=15708 N Clear mopshoe Finish attempt
4. As shown below, the prosthesis is made of two parts a core (Ge=150 ksi) and a tube (G=85 ksi). The prostheses is under torsional torque of 15 lbf.in due to foot movement. a) Determine the maximum torsional stresses in the core and tube. b) Determine the angle of twist 15 Ibf.in 15 lbf.in 15in Diameter 1.5 in Diameter 1in 15 Ibf.in (Answer: a)t, = 23.13 psi; t = 19.67 psi b) = 0.0046 rad)
Clear my choice Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E= 200 Gpa and a Poisson's ratio of 0.3. If a tensile force Fis subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: O F= 5236 N OF=15708N O F= 13090 N OF=10472 N OF=4189 N O F=6283 N Clear my choice Finish attempt NEXT ACTIVITY MENG360 Test -Spring 2020-2021 Jup to
(4) The plunger of an oil pump is held against the operating cam by a spring made of No.10 W&M gage steel wire coiled with an outside diameter of 7%-in. There are five active coils. The open length is 1.1875in. What are the length & stress when a load of 30lb is applied.
Problem 2 330k 198k 132k N -16 in.- 12 in. 12 in. E = 29×10086sa D = 1.07 in (bigger rod) D=107ind 0.618 in. rod) Determine the deformation of the steel rod shown under the given loads. SOLUTION: • Divide the rod into components at the load application points. Apply a free-body analysis on each component to determine the internal force • Evaluate the total of the component deflections. 2-3
EHide bl OP=287 N OP=573 N Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E = 200 Gpa and a Poisson's ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.998 mm. determine the applied force F. Select one: OF=10472 N OF=15708 N OF=6283 N O F= 4189N F = 13090 N OF= 5236 N Finish attempt.. US ACTIVITY O Test-Spring 2020-2021 Jump to...
1. A solid square rod is cantilevered at one end. The rod is 0.8 m long and supports a completely reversing transverse load at the other end of 50 kN. The material is AISI 1060 hot-rolled steel (?? =370 MPa,?? =680 MPa ). Use a design factor of 2 and determine the dimensions of the square cross section for the following cases. Neglect any stress concentration. a. The rod must support this load for 100 cycles. b. The rod must support this load for 104 cycles. c. The rod must have infinite life.