Two squirrels are sitting on the rope as shown. The squirrel at A has a weight of 1.45 lb. The squirrel at B found less food this season and has a weight of 1 lb. The angles and are equal to 49.5 and 59.4° respectively. Determine the tension force in each of the rope segments (7₁ in segment AC, T₂ in segment AB, and T3 in segment BD) as well as the angle a in degrees. A Note the figure may not be to scale. T₁= T₂= T₁= e a= 9 lb deg a B COX0 2013 Michael Swarbom

Two squirrels are sitting on the rope as shown. The squirrel at A has a weight of 1.45 lb. The squirrel at B found less food this season and has a weight of 1 lb. The angles and are equal to 49.5 and 59.4° respectively. Determine the tension force in each of the rope segments (7₁ in segment AC, T₂ in segment AB, and T3 in segment BD) as well as the angle a in degrees. A Note the figure may not be to scale. T₁= T₂= T₁= e a= 9 lb deg a B COX0 2013 Michael Swarbom

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The Answer is one of the options below please solve and circle the correct option .
Draw Front and Side and top with all dimensions please
I need the answer in15 mints please please please best wishes Ahmed
Please help I will give you good ratings
Hi, Could you please help with this question, if you need to take more credits then please feel free. showing working out if possible too please, Thank you
B P. 200 mm 240 mm 60 30 KN Figure (1.15)
Required information Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has a 1.250-inch-thick bar that needs 90° grooves machined into it for precision ground 1.0000-inch diameter cylinders. A sine bar is used by placing different thicknesses under one of the cylinders so that the proper angle is attained. Sally wants the distance between the centers of the cylinders to be D= 5.9 inches. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 7 -1.00000 * How deep should she mill the 90° grooves so that the top of the sine block is 2 inches tall? (Round the final answer to four decimal places.) The depth of the mill should be 7071.067 inches.
When do the actual dimensions occur?
Please help. I need help with all 4 questions. Apply geometric tolerancing to part according to the instructions below. This exercise will provide you with experience in correctly applying and interpreting geometric tolerancing symbology. If you have trouble applying the symbols, page through this unit looking for similar examples. The Hole Bar in this unit is a good reference. Draw symbols and feature control frames clearly and neatly. 1. Establish all necessary basic dimensions. 2. Position the .250 hole within a diameter of .005 RFS relative to datum features A,B,C. 3. Position the three holes within a diamter of .012 at MMC relative to datum features A,B,C. 4. In the front view, identify the upper right corner as point "Y" and the lower left corner as point "X". Apply a profile tolerance of .020 between points X and Y relative to datum features A,B,C. Please refer to the attached image.
‏Generate isometric drawing from multiviews using drawing tools or free - hand . Use approximate proportionate dimensions . Use plane sheet to draw or sketch isometric drawing
Select the correct statement regarding the solid model shown below. pattern1 It is easiest to create the 18 holes in this model by sketching each individual hole and using the extruded boss/base feature. It is easiest to create the 18 holes in this model by sketching one individual hole
How would you determine final dimensions using the plus & minus method for question #D??