Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take d₁ = 30 mm, d2 = 50 mm, and P= 50 kN.P0.9 m125 kN125 KNB1.2 mFind the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.)The average normal stress at the midsection of rod BC isMPa.

Answered: Image /qna-images/answer/36625112-5c6f-4e83-b06f-900e2f215606.jpg

Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take d₁=30 mm, d₂ = 50 mm, and P = 50 kN. P 0.9 m 125 IN 125 KN 1.2 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is MPa.

Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Take d₁=30 mm, d₂ = 50 mm, and P = 50 kN. P 0.9 m 125 IN 125 KN 1.2 m Find the average normal stress at the midsection of rod BC. (Input the answer with the appropriate sign.) The average normal stress at the midsection of rod BC is MPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.3.10P: Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa

See similar textbooks

Similar questions

Answer the ff correctly. The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin. The width of the rectangular bar is 70 mm and its thickness is 15 mm. The bearing stress in the bar cannot exceed 120 MPa. Determine the maximum value of Pmax that can be supported based solely on consideration of the bearing stress in the bar. Note: This question is not asking about any stresses in the support bracket...just bearing stress in the rectangular bar.
Two vertical steel rods support the rigid bar as shown. Initially, the rods are stress-free. Given the data below, determine the stress of rods A and B after the 20 kN load is applied. Neglect the weight of the bar and use E = 200 GPa for steel. L= 3 m D = 3.5 mm A. Stress of rod A (MPa) B B. Stress of rod B (MPa) C. At what temperature AT change would the stresses for both rods be equal? Use a = 11.7 L= 4 m x 10-6 mm/mmC° (C°) D = 5 mm 4m 2m 2m 20 kN
(1) Given: b₁ B P=28 kN Square Bars b₁ = 57 mm (2) Q =9 kN b2 C b₂ = 19mm (3) Q R = 38kN ↑ D b3 = 38mm R WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS.
The rigid bar AB shown below is supported by a steel rod AC having a diameter of 20 mm, and a block. Ignore the weight of AB and AC, and the distributed load on AB is p = 4.0 KN/m. Determine the axial normal stress developed in AC: = ____ MPa. Calculate your answer to 1 decimal place.
ENERAL INSTRUCTIONS: Write your complete solutions legibly on clean sheets of paper. I. Solve the following problems, complete with free body diagrams, clear solutions, and complete final answers. 100 kN 50 kN 1 2 |d1 — 30 тm d2 = 50 mm 1. 100 kN 0.9 m 1.2 m Rods 1 and 2 are welded together and are subjected to the shown loads. Given the measurements shown, determine the average normal stress internally experienced by rods 1 and 2, and specify whether these stresses are tensile or compressive.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
SITUATION 4. Given the figure below, find the: |31 kN 5-25 mm Ф bolts 70 mm 80 mm 80 mm 70 mm 31 kN 370 mm 9. Maximum stress a. 60.23 MPa b. 32.12 MPa c. 65.42 MPa d. O MPa 10. Minimum stress а. 60.23 MPа b. 32.12 MPа c. 65.42 MPa d. O MPa
3. The vertical force F applied at A is 50 kN. Compute the minimumdiameter of the steel wire, if the allowed elongation on steel wire4mm and its stress is limited to 250 MPa. Use Est = 200 GPa. Answer: d = ___________________
gure 1 shows a compound bar with three different diameters, d1-9mm, d2-22mm, and d3-14mm machined from solid aluminium alloy stock, subjected to a tensile load of 30kN. If Young's odulus for the alloy is 69GPA determine the stress in section 2. Answer to be provided in MPa, correct to three decimal places - do not include a unit with your answer. L1 L2 L3 d2 d3 P Figure 1
Find stress of a aluminum cylinder of diameter 12.8mm and gauge length 50.8mm. The force applied is 47,500N.
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 1 and rod 2. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m2. What will be the stress along the face AB? (Cambridge) 12.4 19.0cm A 36 cm 1.60 cm 1.90 cm 1.60 cmT B. +17.5cm