Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 = 30 mm and d2=50 mm, find the average normal stress at the midsection of (a) rod AB, (b) rod BC.

Q: Two members of uniform cross section 50 *80 mm are glued together along plane a–a that forms an…

A: Draw the stress element of the cross-section.

Q: For the connection shown, the average shear stress in the 16-mm-diameter bolts must be limited to…

A: Givend=16mmAverage shear stress=260Mpa

Q: Ex : Two solid cylindrical rods AB and BC are welded together at B and loaded as shown , Knowing…

A:

Q: Two 1.2-kip forces are applied to an L-shaped machine element AB as shown. Determine the normal and…

A:

Q: A 4-m-long steel rod must not stretch more than 3 mm and the normal stress must not exceed 150 MPa…

A:

Q: A short wooden post supports a 6-kip axial load as shown. Determine the stress at point A when (a)…

A: Determine the area and moment of inertia of the cylindrical body,

Q: Portions of a 1/2 x 1/2 -in. square bar have been bent to form the two machine components shown.…

A: Given Data: The coss-sectional area of the squer bar is: 0.5 X 0.5 in2. The allowable stress is :…

Q: A vertical rod is attached at point A to the cast iron hanger shown. Knowing that the allowable…

A: Cross section of the vertical rod at the section a-a To determine the largest downward force and…

Q: The vertical portion of the press shown consists of a rectangular tube having a wall thickness t5 10…

A:

Q: A rod must not stretch more than 6 mm when the tension in the wire is 8 kN. Knowing that E = 105 GPa…

A:

Q: The rigid castings A and B are connected by two 20 mm diameter steel bolts CD and GH and are in…

A:

Q: Two horizontal 9-kips forces are applied to pin B of the assembly shown. Knowing that a pin of…

A:

Q: [2.37] The 1.5 m concrete post is reinforced with six steel bars, each with 28 mm diameter. Knowing…

A:

Q: A cast-iron machine part is acted upon by the 3 kN-m couple shown. Know-ing that E= 165 GPa and…

A: Given data Couple acting on the machine part, M = 3 kN-m. Draw the cross-section of the beam,…

Q: Knowing that the allowable stress in section ABD is 10 ksi, determine the largest force P that can…

A: Given data: The allowable stress in the section ABD is; σallow=10 ksi. Evaluate the cross-section…

Q: Link BD consists of a single bar 30 mm wide and 12 mm thick. Knowing that each pin has a 10 mm…

A:

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that P =…

A: (a) Consider the Rod AB. The rod AB is only experiencing a force (tension) P along the left…

Q: The Bars of the Pin-connected frame as shown are each 30mm and 60mm in section. Determine the…

A: Given:   σT=100 MPaσC=80 MPaSection=60 mm×30 mm The free-body diagram of the frame considering…

Q: A thin strap is wrapped around a solid circular rod of radius c=20 mm where Force is applied, as…

A:

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that dj =…

A:

Q: 2.94 Knowing that P 38 kN, determine the maximum stress when (a) r = 10 mm, (b) r = 16 mm, (c) r =…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall…

A:

Q: The AB and BC rods have a diameter of 5mm. If a load P = 2kN is applied to the ring, determine the…

A:

Q: The vertical portion of the press shown consists of a rectangular tube having a wall thickness t5 10…

A: Given data: The thickness of the tube is t = 10 mm. The maximum load is P = 20 kN. The length of…

Q: Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: The bearing stress at A in member AB is 67488 psi.

Q: The elevation of the platform is controlled by two identical mechanisms, only one of which is shown.…

A: Load = 1500 lb  Here we need to draw free body diagram and solve the sum  So here I am drawing it in…

Q: An axial centric force of magnitude P= 450 kN is applied to the composite block shown by means of a…

A: P= 450 kN h = 10 mm  Normal stresses in brass core and aluminum plates are to be calculated.

Q: An 18-m-long steel wire of 5-mm diameter is to be used in the manu-facture of a prestressed concrete…

A: Given is: Length of steel wire, l=18m Diameter of the wire, d= 5mm = 0.005m Stretch or change in the…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d1 =…

A: Write the expression for stress developed in the cylindrical rod.

Q: A rod must not stretch more than 6  mm when the tension in the wire is 8 kN. Knowing that E = 105…

A:

Q: An offset h must be introduced into a solid circular rod of diameter d. Knowing that the maximum…

A: Given data: Maximum eccentric load stress must not exceed 4 times the center load stress, σe = 4σc.…

Q: Knowing that P= 38 kN, determine the maximum stress when (a) r= 10 mm, (b) r =16 mm, (c) r= 18 mm

A: Given that, Allowable load, P=38 kN,Width at upper section, d=60 mm,Width at lower section, D=120…

Q: Knowing that the clamp shown has been tightened on wooden planks being ghued together until P= 900…

A:

Q: 13 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that…

A:

Q: Two L4 x 3 rolled-steel angles are bolted together and used to sup-port the loading shown. Knowing…

A: Draw the free body diagram.

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: [English] Two solid cylindrical rods AB and BC are welded together at B and Knowing that dį = 60 mm…

A: Given data: The diameter of rod AB, d1 = 60 mm. The diameter of rod BC, d2 = 40 mm. Part (a)…

Q: Two horizontal 9-kips forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: A steel control rod is 5.5 ft long and must not stretch more than 0.04 in. when a 2-kip tensile load…

A: Given that: Modulus of elasticity,  Tensile load,  Let we have a steel rod of natural length  long.…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A:

Q: Knowing that the clamp shown has been tightened until P= 400 N, determine (a) the stress at point A,…

A: Given Applied load = 400 N To find Stress at point A Stress at point B Location of neutral axis

Q: Knowing that the magnitude of the horizontal force P is 8 kN, deter-mine the stress at (a) point A,…

A: P=Compressive force=8 kN

Q: Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A:

Q: of the assembly shown. Knowing that a pin of 20 mm diameter is used at each connection, determine 2…

A:

Q: A 4.8-ft-long steel wire of 14-in. diameter is subjected to a 750-lb ten-sile load. Knowing that E5…

A: Given:Length of wire,L=4.8ftDiameter of wire,D=0.25inApplied load,P=750lbElastic modulus,E=29×106psi

Q: The tube shown has a uniform wall thickness of 12 mm. For the given loading, determine (a) the…

A: Given: Wall thickness if the tube is 12 mm.

Q: The four forces shown are applied to a rigid plate supported by a solid steel post of radius a.…

A: Given data: The value of force P is P=24 kips The value of radius a is a=1.6 in

Q: 2. The 4-mm-diameter cable BC is made of a steel with E = 200 GPa. Knowing that the maximun stress…

A: