Two simple elements R=12 , C=31.3 µF are connected in series and a voltage of V=100 cos(2000t -20°) volts is applied to them. The same two elements are connected in parallel with the same applied voltage. I) II) Find the current intensity in the series circuit, for the instant t=0.1 s Find the current intensity in the parallel circuit, for the instant t=0.01 s

Two simple elements R=12 , C=31.3 µF are connected in series and a voltage of V=100 cos(2000t -20°) volts is applied to them. The same two elements are connected in parallel with the same applied voltage. I) II) Find the current intensity in the series circuit, for the instant t=0.1 s Find the current intensity in the parallel circuit, for the instant t=0.01 s

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter18: Resistive-inductive Parallel Circuits

Section: Chapter Questions

Problem 1PA: Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter...

See similar textbooks

Similar questions

Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
Determine the DC currents (B. Ic and le) and de juncion voltages (VBE, VCE and Vca) mA. Ic ma, E mA VBE= V. VCE Vand VCB Use 2 decimal places. RB Use the following values: VBB = 3V RB = 4 kQ Rc = 166 0 Vcc = 19 V BDC = 70 %3D %3D VCC RC VBB
Please show your detailed solution Number 14 The current in a series inductive circuit is 7.5 A at 25 Hz. The circuit takes 425 W, and the power factor is 0.47. The resistance of the circuit is A. 7.32 ohms C. 7.98 ohms B. 7.86 ohms D. 7.56 ohms
5 The voltmeters in the figure measure RMS voltages. If V, = 23 V and V, = 14.5V what is V3? %3D C R eee V2 V3 23 V None of them 8.5 V 4.5V 37.5 V O 14.5 V
60. Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V de voltage source. 61 Datermine the volto in the girRuit F Figura 1 1?
Calculate the branch currents and the total equivalent current of the complete circuit in Figure Q3. Draw the current phasor diagram for the complete circuit. The alternating Voltage source has an amplitude of 10 Vm Sine 50 Hz CI 1 mF C2 1.2 mF Figure Q3 RI 22 52 C3 0.4 mF R2 44 92
assume that the voltage drop across the resistor ER is 78 v the voltage drop across the capacitor EC is 104 v and the circuit has a total impedance z of 20 ohms the frequency of the ac voltage is 60 hz find the missing values. fine the missing vaules
3. Sketch the current waveform for the circuit in Figure below. The diac has a breakover potential of 20 V. IH = 20 mA. 25 V rms R 1.0 ΚΩ
The complex volt amperes in a series circuit are (4300- j2500) and the current is (25 + j43.3)A.Find the applied voltage.
Q5] find the current of the resistance 1892 if the value of the source is 7.4sin(100πt-44) volt HH 1mF R1 ww 18Q R4 •14Ω 3.9mF 13.100, 78.163⁰ mA O 14.100, 78.163⁰ mA O 15.100, 78.163⁰ mA 0.093H V1
Find the value of C in microfarads and L in henries. 1, = 3 sin(377r+ 60°) R120X₁20 X 50
If an electrical circuit draws 100W + J100VAR from a sinusoidal source, then what would the circuit be? Explain why. a) a pure resistor circuit b) a series or parallel R-L circuit c) a series or parallel R-C circuit d) a series L-C circuit