Two rigid tanks are connected by a valve. Tank A contains 0.25 m3 of water at 450 kPa and 75 percent quality. Tank B contains 0.55 m3 of water at 300 kPa and 250oC. The valve is now opened, and the two tanks eventually come to the same state. Determine the pressure and the amount of heat transfer when the system reaches thermal equilibrium with the surroundings at 25oC. Handwritten pls

Two rigid tanks are connected by a valve. Tank A contains 0.25 m3 of water at 450 kPa and 75 percent quality. Tank B contains 0.55 m3 of water at 300 kPa and 250oC. The valve is now opened, and the two tanks eventually come to the same state. Determine the pressure and the amount of heat transfer when the system reaches thermal equilibrium with the surroundings at 25oC. Handwritten pls

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter1: Heat, Temperature, And Pressure

Section: Chapter Questions

Problem 6RQ: One British thermal unit will raise the temperature of _____ 1b of water _____F.

See similar textbooks

Similar questions

4. Arigid tank contains 2 kg of air. The tank is initially at 25°C. The tank is heated until the pressure doubles. Determine the final temperature in Kelvins and the change in internal energy in kJ.
The frictionless piston and cylinder contain 1 kg of water. The initial pressure and volume are each pressure of 100kPa 0.25 m^3 (state 1). The system was gradually heated and when the volume of water in the cylinder became four times the initial volume (state 2), the piston was fixed and heating was continued until the water pressure reached 300 kPa (state 3). (1) Find the final temperature in the cylinder (2) Find work during this process (3) Find the amount of heat transfer during this process. Try to approximate this process on a P-v diagram.
.A kilogram of Argon gas( MW= 40 kg/kmol, k=5/3) is in a piston cylinder set-up. Initially, it has pressure of 30kPa and volume of 0.2m3 and expanded to 20 kPa due to heat transfer. If the process is said to be isovolumic, find initial and final temperatures.
QI/ the cylinder contains 0.2 kg a refrigerant R-134a of saturated water liquid at 20 °C. The stops location corresponds to 50% of the initial volume. The water is heated to the final state at 50 °C. If the piston reaches the stops? and what are the initial and final pressure. R-134 a
wer.. 2. Ammonia weighing 22 kgs is confirmed inside a cylinder equipped with a piston has an initial pressure of 413 KPa at 38C. If 2900 KJ of heat is added to the ammonia until its final pressure and temperature are 413 KPa and 100C, respectively, what is the amount of work done by the fluid in KJ?
During processing in a steel mill, a 375kg steel casting at 800 degrees is quenched by plunging it into a 500-gal oil bath, which is initially 75 degrees . After the casting cools and the oil bath warms , what is the final tempertature of the two? The weight per unit volume of the oil is 7.5 lb/gal.
A system including a movable part, a piston, undergoes two stages. In the first stage, the system is compressed at a constant temperature. Here, the volume of the system reduces from 1.8 to 0.4 liters as a result of this process.In the second stage, heat is supplied to the system at the resulting constant pressure which was obtained at the end of the first stage.If at the beginning of the first stagethe pressure is1 atm, what would be the volume of this system after supplying 320 kJ of heat to the systemin the second stage? www
A closed rigid tank has a capacity of 2.5 m3. It holds air at 400 kPa and 18 deg C. Heat is added until the temperature is 350 degC. Determine the heat added in kJ. Given a vacuum pressure of 165 mmHg. The barometric pressure is 745 mmHg. Find the absolute pressure in kPa. What is the amount of dry steam flow to an engine, which is supplied with 4500 kg per hour wet steam with a quality of 80%?
A cylindrical vessel with a diameter of 8 inches and 5 feet long contained acetylene at 300 psi gauge and 82°F. After some amount of acetylene was used, the pressure was reduced to 190 psi gauge and the temperature was 74°F. The gas constant of acetylene is 59.35 ft-lb:/lbm-°R. Determine the following: 1. What is the initial mass in Ibm of the acetylene inside the vessel? 2. What proportion in percentage of acetylene was used? 3. What volume in ft would the used acetylene occupy at 30 psig and 80°F?
One kilogram of saturated solid water at the triple point is heated to saturated liquid while the pressure is maintained constant. Determine the work and the heat transfer for the process, each in kJ. Show that the heat transfer equals the change in enthalpy of the water in this case.
B2. The heat energy of 1605 kJ is supplied to saltwater in the steam generator to heat from 25°C to 104°C for the generation of water vapor, Take the density & specific heat of the solution as 1028 kg/m³ & 3 J/kg°K respectively. Determine the quantity of saltwater in the steam generator. I Solution: i) Change in Temperature (in K) ii) Mass of the saltwater (in kg) iii) Quantity (Volume) of salt water (in m³)
A pressure cooker operates by cooking food at a higher pressure and temperature than is possible at atmospheric conditions. Steam is contained in the sealed pot, with a small vent hole in the middle of the cover, allowing steam to escape. The pressure is regulated by covering the vent hole with a small weight, which is displaced slightly by the escaping steam. Atmospheric pressure is 1 bar, the vent hole area is 7mm2, and the pressure inside should be 2.75 bar. What is the mass in kg of the small weight?