Solve question no.07 and show the solution.Note: The answer is given on the bottom right side of the image, just show the solution on how to get it.Thanks!!! 7. Two parallel circuits comprise respectively (i) a coil of resistance 20 Qand inductance 0.07 H and (ii)a capacitance of 60 µF in series with a resistance of 50 N Calculate the current in the mains and thepower factor of the arrangement when connected across a 200-V, 50-Hz supply.[7.05 A ; 0.907 lag] (Elect. Engg. & Electronics, Bangalore Univ.)

Kirchoff's voltage and the current law is an important law in the electrical networks which is used…

Two parallel circuits comprise respectively (î) a coil of resistance 20 Nand inductance 0.07 H and (ii) a capacitance of 60 µF in series with a resistance of 50 N Calculate the current in the mains and the power factor of the arrangement when connected across a 200-V, 50-Hz supply. [7.05 A ; 0.907 lag] (Elect. Engg. & Electronics, Bangalore Univ.)

Two parallel circuits comprise respectively (î) a coil of resistance 20 Nand inductance 0.07 H and (ii) a capacitance of 60 µF in series with a resistance of 50 N Calculate the current in the mains and the power factor of the arrangement when connected across a 200-V, 50-Hz supply. [7.05 A ; 0.907 lag] (Elect. Engg. & Electronics, Bangalore Univ.)

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter3: Magnetic Starters

Section: Chapter Questions

Problem 30SQ

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
1. Enumerate five formulas for five series connected inductances across Vt source and draw the circuit. 2. Enumerate five formulas for five parallel connected inductances across Vt source and draw the circuit.
The AC V-meter in the figure is designed to measure the RMS valueof the input sinusoidal voltage u(t). The diodes are assumed to beideal; M is a moving-coil type measuring unit with Ri=2k (internalresistance) and im=100A (current for full-scale deflection).a) Draw the current through M in scale and calculate R1 for anominal voltage of 100V.b) The class of the measuring unit is given as 0.5. Calculate themaximum acceptable tolerance for the resistors (all of thesame tolerance), if the V-m is required to be of the class 1.5 max.
Question- A solar cell of 350 V is feeding power to an ac supply of 440 V, 50 Hz through a 3-phase fully controlled bridge converter. A large inductance is connected in the dc circuit to maintain the dc current at 20 A. If the solar cell resistance is 0.5 Q, then find the period for which each thyristor be reverse based.
A series circuit consisting of 10 ohm resistance and 60 mH inductance is connected to a 220-volt, 50-hertz source. Determine the voltage drop across the inductance.
Q. 14. At high frequencies, the shunt resistors used for current measurement will have a higher reactance part due to: A) Stray capacitance C) High reactance occurs at low frequencies B) Stray inductance D) A & B
5. An alternating current bridge is arranged as follows: The arm BC and DA consists of non-inductive resistance of 800 Q each. A balance is obtained when resistances of the arms DE and CD of non-inductive variable resistances of 200 N, 1k n respectively. The arm EC of a capacitor of 1 µF capacitance. The alternating current source is connected to A and C and the telephone receiver to B and E. Calculate the resistance and inductance of arm AB. Also find Q factor, when supply frequency is 1500HZ.
3. For a parallel circuit of 20 ohms resistor and a 10 ohms inductor, is connected to a 110/60 cps Volts source a) find the Impedance b) determine current IR c) determine the current IL d) find the inductance.
1. A resistor of 2502, is connected in series with a 1.5 H inductor, cross a 100 V, 50 Hz supply. Çalculate (a) the current flowing, (b) the circuit phase angle, (c) the p.d. developed across each component and (d) the power dissipated.
In a series circuit with the following devices to a 230volts 60Hz supply with a resistor in the range of 300 ohms and 990 ohms. What are the steps in calculating the impedance ...
Q5: Two capacitors (2#F, 8 #F) are connected in series across 100 volt. Then these capacitors are connected in parallel. How much the charge for two cases. 06: Capacitor 20 HF is connecting with 55 volt, 50 Hz. Calculate the current for the capacitor. When this capacitor is connecting with 10 volt, 50 Hz. How much is the current.
Two coils are A and B are connected in series to a supply of 230V, 50HZ. Coil A has an inductance of 0.2H and a resistance of 20 Q, and coil B has an inductance of 0.05H and a resistance of 60 Q. Calculate the current and its phase angle relative to the supply voltage. Also determine the voltage across each coil.