Two large plates are parallel. Considering that the distance between the plates is 5 mm and that this space is filled with an oil of dynamic viscosity 0.02 N.s/m?, determine the force necessary to drag a 1 m square plate, thick 3 mm, positioned at equal distance from the two plates, at a constant speed of 0.15 m/s. 5 mm Oil 3 mm 1 m

Two large plates are parallel. Considering that the distance between the plates is 5 mm and that this space is filled with an oil of dynamic viscosity 0.02 N.s/m?, determine the force necessary to drag a 1 m square plate, thick 3 mm, positioned at equal distance from the two plates, at a constant speed of 0.15 m/s. 5 mm Oil 3 mm 1 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 416 mm?, 622 mm?, and 281 mm? respectively.Determine the change in length (in mm) of the bar if P = 27177 N.The moduli of elasticity are 81.33 GPa for bronze ,73.05 GPafor aluminum , and 200.23 GPa for steel . Round off the final answer to four decimal places. Bronze Aluminum ЗР Steel 2P P 4P -0.6 m 1.0 m- 0.8 m
Help me urgent Two forces are applied ti the bar shown in the figure. Determine the normal and shearing stresses at point A, B and C?
In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a cross-sectional area of 410mm2. The stresses in AC and BD are limited to 110MPa and 53MPa, respectively. Find the magnitude P of the largest additional vertical force that can be applied to the bar.___________kN in 2 decimal places Take note: Write it on a paper, hand written showing correct answer.
The BC rod in the carrier system shown in the figure has a circular cross section. diameter 25 mm and Tensile Strength 210 MPa and Modulus of Elasticity 2x105 It is MPa. Since a load of 640 kg is hung on the D end of the system; For BC bar: a) Tensile stress, b) Safety coefficient, c) Calculate the length change amount.
A frame structure carries a sign, as shown in the figure below. The sign ismade of steel (with mass density of 8000 kg/m3) and of uniform thickness. What is the maximum thickness t_max of the sign such that the allowable shear forceand bending moment within the frame structure are not exceeded: Vallow= 8 kN and Mallow= 12 kN·m. Assume the frame members are weightless. There are pins at points A ,B, andC. The sign weight is transferred through cables CE and DF.
PROBLEM 4 - A solid shaft given below is made from two segments: AC has a diameter of 15 mm and CB has a diameter of 10 mm. Determine the support reaction at point B and clearly statie its direction if it the shaft is fixed at points A and B and is subject to a torque 7' at point D. Take the shear modulus as 50 GPa. Write your final answer in the textbox below. Hint: J0.5ne, where e is the radius. 15 10 mm D. B. T 20 Nm 1m 0.5 m 2 m Wall
Example 21.18. A solid circular steel rod 6 mm in diameter and 500 mm long is rigidly fastened to the end of a square brass bar 25 mm on a side and 400 mm long, the geometric axis of the bars lying along the same line. An axial tensile force of 5 kN is applied at each of extreme ends. Determine the elongation of assembly. For steel E = 200 GPa and for brass E₁ = 90 GPa
A Homogeneous 2700 Kg Bar AB Is Supported At Either End By A Cable As Shown In The Figure. Determine The Stress In The Bronze Cable If The Cross Sectional Area Of The Bronze And Steel Cables Are 55 Mm 2 And 35 Mm 2, Respectively. Bronze L = 4 M Steel L = 3 M A 10 M B 240 MPa 126 MPa 135 MPa 150MPa
Q2: A rigid bar is suspended from two wires of equal lengths 250 cm as shown below. Take E,= 210 GPa, E=110 GPa. All data in the Table below. Find: 1. Distance of the load (P) from the bronze wire. 2. Stresses developed in steel and brass wires. - Bronze Wire 250 cm Distance Steel wire Dia Dia Distance P (N) (steel) Сopper between two wires (mm) mm mm 26 35 850 8000
A steel tube is 5 millimeters thick and has an outside diameter of 60 millimeters. It is being used as a compression member. If the axial normal stress in the member is only limited to 200 megapascals, determine the maximum load P in kN that the member can support. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and the final answers to 3 decimal places.
In the figure below, the beam is cantilevered from the wall. The connection of the beam to the wall can be considered a general interaction. The beam has a uniform density, so it will be subject to a weight force applied mid-way between points A and B. length from point A to point B =10.0 meters; weight applied at point B = 1.00 kN; beam weight = 0.500 kN Beam embeded in cwalla cautilever B A What is the magnitude and direction (relative to the x-y coordinate system shown in the upper left portion of the figure) of the horizontal and vertical components of the wall support? horizontal = 0 N, vertical = 1.50 kN O horizontal = 1.50 kN, vertical = 0N O horizonatl = O N, vertical = 1.00 kN O horizontal = ON, verttical = 2.00 kN