Two kilograms of water is contained in a piston-cylinder device where a linear spring is attached to the piston, as shown in the figure. The spring was initially at rest, when the pressure of water inside the cylinder was 100 kPa and the volume was 0.2m³. Heat is then added to the system. As the piston first hits the stops, it is known that the volume was 0.8 m³ and the temperature was 600°C. The heating is continued until the pressure reaches 1.2 MPa. Determine the final temperature, sketch the process on a P-V diagram, and calculate the work done during the entire process. H,0

Two kilograms of water is contained in a piston-cylinder device where a linear spring is attached to the piston, as shown in the figure. The spring was initially at rest, when the pressure of water inside the cylinder was 100 kPa and the volume was 0.2m³. Heat is then added to the system. As the piston first hits the stops, it is known that the volume was 0.8 m³ and the temperature was 600°C. The heating is continued until the pressure reaches 1.2 MPa. Determine the final temperature, sketch the process on a P-V diagram, and calculate the work done during the entire process. H,0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

hi, can you solve this question ? The A and B tanks given in the figure are separated from each other by the closed valve between them. The water vapor in tank A has a volume of 0.2 m3, a temperature of 150 ° C and a pressure of 100 kPa. Tank B is filled with saturated water vapor in a volume of 0.3 m3 at a pressure of 300 kPa. Then, the valve between the tanks is opened and the final pressure is 175 kPa as a result of the mixing of the fluids in the tanks with each other and sufficient heat transfer. According to this:a) Temperature (C) and phase of the fluid in the final state;b) Find the amount of heat transfer in the process result.
Air is compressed into a 0.5m3 rigid tank until the pressure changes from 120 kPa vacuum pressure to gage pressure of 320 kPa. If the air can cool to 450C. What will be the initial temperature of the air?
Determine the work done by the expanding gas using the trapezoidal rule. from the data in the image
Ammonia with MW=17, weighing 22kg is confirmed inside a cylinder equipped with a piston has initial pressure of 413kPa and 48C. if 2900kJ of heat is added until the final pressure is 413kPa and final temperature is 100C. Determine the change in internal energy kJ
Refrigerant 134a expands in a piston-cylinder assembly from p₁= 200 lb/in² and T₁ = 140°F to p₂ = 30 lb/in² and T₂ = 80 °F. The mass of refrigerant is 0.46 lb. During the process, the work done by the refrigerant is 4.32 Btu. Kinetic and potential energy effects are negligible. Determine the initial volume of the refrigerant, V₁, in ft³, and the heat transfer for the process, in Btu. Step 1 * Your answer is incorrect. Determine the initial volume of the refrigerant, V₁, in ft³. V₁= 0.105743 ft3
ASAP please
the initial temperature (T1) in (oC) is A piston-cylinder device contains water of quality x = 0.7 and pressure 200 kPa with an initial volume of 100 Liter. The system is now heated in isobaric process to a final temperature of 200°C. Piston-cylinder device water, x₁ = 0.7 P₁ = P₂ = 200 kPa Q₁2V₁ = 100 Liter T2 = 200 C
THERMOFLUID A frictionless piston-cylinder contains 3.30 kg of saturated water at 1 MPa. The water is expanded at constant pressure until its temperature rises to 270 °C. The image of the system and process are shown in Figure 3. Determine: The final volume of water in cylinder, and sketch the process in P-V diagram