Two identical plates are connected by two 25-mm diameter rivets as shown. Consider the following dimensions: B = 110 mm t = 25 mm x = 18 mm The allowable stresses of the plate are the following: Normal stress = 15.5 MPa Bearing stress = 4.25 MPa Shearing stress = 6.5 MPa Determine the maximum force P: A. Considering the normal stress: P = B. Considering the bearing stress: P = C. Considering the shearing stress: P = KN KN kN

Two identical plates are connected by two 25-mm diameter rivets as shown. Consider the following dimensions: B = 110 mm t = 25 mm x = 18 mm The allowable stresses of the plate are the following: Normal stress = 15.5 MPa Bearing stress = 4.25 MPa Shearing stress = 6.5 MPa Determine the maximum force P: A. Considering the normal stress: P = B. Considering the bearing stress: P = C. Considering the shearing stress: P = KN KN kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

what The answer 15 for this: 23,500 (1 + 0.031) 30 4.3/ number • answer must be report to the proper of significant digits A a showe all work Bea
The objective of the assignment problem is to assign the jobs, then the assignment cost will be O a. Maximum O b. Minimum Oc. Maximum and Minimum O d. None
How did you get the Tsat values
If a critical point at structural element is subjected to the stress shown on the 2D element, determine the factor of safety (FS) against rupture according to the maximum principal stress theory. The material has an ultimate tensile stress Sult = 500 Mpa. 150 Mpa 50 Mpa 250 Mpa
Find warrk done
1 The basic drilling process is that a at the bottom of_ grinds a hole through the rock layers.
Determine the absolute maximum shear stress of the stress state acting on the element shown in the following figure. 120 Mpa 300 Mpa 50 Мра
Give at least 7 machine/equipment and their uses. PLEASE TYPE THE ANSWER
Given the table of results find the following. Give answers in KW. Please show all working out Rate of heat transfer to evaporator from the chilled water Rate of heat transfer from condenser to the cooling water Rate of heat transfer to refrigerant in Evaporator using enthalpy values Rate of heat transfer from refrigerant in Condenser using enthalpy values Work input from the compressor to the refrigerant using enthalpy values
Create a list of operations for the blueprint provided below. The list of operations must be in chronological order. • All units are in millimeters• Drill depth: 15mm• Raw material dimension: o Body: 65mm longo Cap: 30mm long• Note: Some corners are chamfered so don’t forget to include it in operations
hand written plz Answer the following questions using the information provided in this unit. Know and Understand 1. True or False? The primary purpose of section views is to help feature exterior detail without using hidden lines. For the next three terms, match the three types of lines to the three descriptions. Answers are used only once. 2. Cutting-plane line 3. Section line 4. Short break line A. Not exclusive to section views, but needed for broken- out sections. B. Drawn thick in a view adjacent to the section view. C. Drawn thin, and usually continuous, but sometimes dashed. 5. Of the following, which is not a type of section view featured in this unit? A. Full B. Half C. Quarter D. Offset 6. True or False? The preferred dividing line between the two halves of a half-section view is the visible line. 7. An object with a number of odd features, such as spokes or holes, often has a(n) section so the odd features can be rotated around the axis into a vertical cutting plane,…
TYPEWRITTEN ONLY PLEASE UPVOTE. DOWNVOTE FOR HANDWRITTEN. DO NOT ANSWER IF YOU ALREADY ANSWERED THIS