Two identical (in terms of voltage and power ratings) transformers A & B are designed to ru at different frequencies. Transformer (A) is to run at 250 Hz, while the second is to run at 5C Hz. O Transformer A is heavier than Transformer B. O Transformer B is heavier than Transformer A. Transformers A & B have the same weight.

Two identical (in terms of voltage and power ratings) transformers A & B are designed to ru at different frequencies. Transformer (A) is to run at 250 Hz, while the second is to run at 5C Hz. O Transformer A is heavier than Transformer B. O Transformer B is heavier than Transformer A. Transformers A & B have the same weight.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter4: Symbols

Section: Chapter Questions

Problem 7SQ: The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d....

See similar textbooks

Similar questions

In the single-phase, three- winding, transformer, the primary current is equal to lo at the condition of ints there is no load on tertiary windings the current in secondary windings equal to zero the resistances (R1, R2, and R3) in transformer windings are equal the inductances (L1, L2, and L3) in transformer windings are equal.
The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
For a short-circuit test on a 2-winding transformer, with one winding shorted, can you apply the rated voltage on the other winding? (a) Yes (b) No
What is the maximum volt-ampere rating of transformers supplying Class 2 systems? ___________
Three single-phase two-winding transformers, each rated 3kVA,220/110volts,60Hz, with a 0.10 per-unit leakage reactance, are connected as a three-phase extended autotransformer bank, as shown in Figure 3.36(c). The low-voltage winding has a 110 volt rating. (a) Draw the positive-sequence phasor diagram and show that the high-voltage winding has a 479.5 volt rating. (b) A three-phase load connected to the low-voltage terminals absorbs 6 kW at 110 volts and at 0.8 power factor lagging. Draw the per-unit impedance diagram and calculate the voltage and current at the high-voltage terminals. Assume positive-sequence operation.
What two types of chime transformers for Class 2 systems are listed by UL? ___________________________ ___________________________
What are the necessary conditions for connecting electrical transformers in series?
Label the terminals of the transformers in Figure 3 according to their proper polarity markings. Transformer 1: additive polarity Transformer 2: subtractive polarity Transformer 3: subtractive polarity
37. If the impedance triangles of two transformers operating in parallel are not identical in shape and size, the two transformers will (a) share the load unequally (b) get heated unequally (c) have a circulatory secondary current even when unloaded (d) run with different power factors. 38. Two transformers A and B having equal outputs and voltage ratios but unequal percentage impedances of 4 and 2 are operating in parallel. Transformer A will be running over-load by. ******* percent. (a) 50 (b) 66 (c) 33 (d) 25
• If the transformer has N₁=1,000 turns and N₂ = 5,000 turns. What will be the primary Power, (P₁), comparing to the secondary power (P₂)? P1 will be 5 Times lower than P2 P1 is equal to P2 P1 is 50 times lower than P2 P1 will be 5 times higher than P2
The equivalent circuit impedances of a 20-kVA, 8000/240-V, 60-Hz transformer are to be determined. The open-circuit test and the short- circuit test were performed on the primary side of the transformer, and the following data were taken: Open-circuit test (on primary) Short-circuit test (on primary) 8000 V V= 489 V I0.214 A 2.5 A P= 400 W P= 240 W Find the impedances of the approximate equivalent circuit referred to the primary side, and sketch the circuit.
During routine tests of a three phase transformer, measurements of DC resistance between windingterminals is noted down. What kind of information can be obtained from the values so noted?