Two blocks are being pushed along an incline. Block A weighs 7.00 kg and block B weighs 14.00 kg. The coefficient of non-sliding friction between block B and the surface of the incline is 0.200 and the coefficient of sliding friction is 0.1000. Assume that the coefficient of friction between the two blocks are too high to cause sliding between the two blocks. The applied force is 185 N. 185 N 40°

Two blocks are being pushed along an incline. Block A weighs 7.00 kg and block B weighs 14.00 kg. The coefficient of non-sliding friction between block B and the surface of the incline is 0.200 and the coefficient of sliding friction is 0.1000. Assume that the coefficient of friction between the two blocks are too high to cause sliding between the two blocks. The applied force is 185 N. 185 N 40°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

BRAIN EXERCISE PROBLEM 1 Determine the maximum shear stress, maximum flexural tensile stress and maximum flexural compressive stress of the beam. The dimensions of the cross-section of the beam are a = 300 mm, b = 150 mm and c = 50 mm. A 30 KN/m D. Lopez www. 10 KN 2.00 B C 20 KN/m D wwwww. 1.00 1.00 2.00 in meters E Figure A: Overhanging Beam C a
A soil sample (sand) obtained from trench has water content of 38%. The specific gravity of solid is 2.65. Determine the maximum permissible upward force if factor of safety is 3.
3. Determine if the tractor which has a weight of 8000 lb with center of gravity at G, can push the 550-lb log up the incline. The coefficient of static friction between the log and the ground is 0.5, and between the rear wheels of the tractor and the ground 0.8. The front wheels are free to roll. Assume the engine can develop enough torque to cause the rear wheels to slip. 1.25 ft B 2.5 ft |10° 3 ft -7 ft
A house with 932 kN weight is built on a steep slope defined by points A, B, and C. To help assess the possibility of slope failure (mud slide), determine the components of the weight in directions normal (perpendicular) to the slope. The rectangular form of the weight and the component of the weight perpendicular to the slope defined by the points A, B, and C.
SITUATION. An 8-m long ladder weighing 900 N is shown in the figure. It is required to determine the horizontal force P that must be exerted at point C to prevent the ladder from sliding. The coefficient of friction between the ladder and the surface at A and B is 0.20. BN W = 900 N %3D B, 4m 4.59m 2 m 35° A, AN 6.55m Determine the required force P. B.
For a gravity dam, the coefficient of friction (µ) is 0.66 and the ratio of restoring force to overturning force is 2.4. Then factor of safety against sliding is
For the dam cross-section shown below, determine the minimum value of b such that the resultant force crosses the base within the middle thirds near the toe. The coefficient of static friction between the base of the dam and the foundation is 0.60. After computing the minimum value of b compute the corresponding the factors of safety against sliding and overturning. What is the maximum soil pressure in KPa? Consider two cases: (a) neglecting hydrostatic uplift. (b) considering hydrostatic uplift that varies from 80% of full static head at the heel to zero at the toe. Vw.s. 6 m 18 m (s-2.20) 6 m
423 N is also wrong. Please answer correctlg
a simply supported beam with a hinge on one end and a roller support at the other end is to carry a uniformly distributed load of 25kn/m 1. determine the slope 2. determine the deflection
Fast fast fast
A simply supported beam, having the following properties: 5.5 m length, Mcr = 30 kN-m, Ig = 7000x10^6 mm^4, Icr = 3000x10^6 mm^4, uniformly distributed dead load = 5 kN/m, uniformly distributed live load = 7 kN/m, Ec = 21,000 MPa. Determine the computed value of instantaneous deflection (DL+LL)