Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued on the contact surfaces. The glue to be used can safely provide a shear strength of 135 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 10 kips. Note that a gap of 0.5 in. is required between boards (1) and (2). (1) O 12.85 in. O 14.78 in. O 7.72 in. O 9.47 in. O 11.75 in. 0.5 in. 6 in. (2) P

Two 6-in.-wide wooden boards are to be joined by splice plates that will be fully glued on the contact surfaces. The glue to be used can safely provide a shear strength of 135 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 10 kips. Note that a gap of 0.5 in. is required between boards (1) and (2). (1) O 12.85 in. O 14.78 in. O 7.72 in. O 9.47 in. O 11.75 in. 0.5 in. 6 in. (2) P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The strain at point A on the bracket has components €g = 330 (10-6), e, = 560 (10-6), Yxy = -570 (10-6), e; = 0. Correct Part B Determine the maximum shear strain in the x - y plane. = 6.15x10-4 'in-plane Submit Previous Answers Correct Part C Determine the absolute maximum shear strain. (Figure 1) Figure < 1 of 1 vec -4 Yaa = 7.99 • 10 max Submit Previous Answers Request Answer X Incorrect; Try Again
ABDE rigid rod with single action rivet from point A, point B Connected with BC rod. B and C points of the rod are fence effect rivets. The maximum shear stress that the rivets can bear is 550 MPa, that of the BC bar Since the maximum tensile stress is 440 Mpa, the safety factor FS = 2; 1 ) Calculate the diameter of rivets A and B 2 ) Calculate the diameter of the BC rod
WELDED CONNECTIONS: THE BRACKET SHOWN IN THE FIGURE IS WELDED ON ONE SIDE OF A STEEL COLUMN WITH 800 mm OF 6 mm FILLET WELD. DETERMINE THE MAXIMUM SHEAR STRESS ON THE WELD.
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
3) will upvote anyone who will answer
QL/ Twe rad have the Same cross- Sectional area; Mad from steel anel Bron ze as shown in fig1. Find the stress in each rood when Est = 200GPa j Eb=83Gpa. br st 3m 30 30 Fig1
Q2. Design a rivet that is utilized in a double riveted butt joint which connects two 12 mm thick plates. The efficiency of riveting joint is 80% and the pitch is 80 mm. If the allowable stresses for the plate material are (tensile stress o 100 MPa, shear stress - 75 MPa, bearing stress oc= 180 MPa) and for the rivet material are (tensile stress o-120 MPa, shear stress T-90 MPa, bearing stress 6 = 200 MPa), use F.S. = 1.
Please answer the questions on the picture and draw free-body diagram make sure you show all of your work, Thank you for your help!
The aluminum rod AB (Gal = 27 GPa) is bonded to the brass rod BD (Gbr = 39 GPa). The portion CD of the brass rod is hollow and has an inner diameter of 40 mm. If the allowable shear stresses for the aluminum and brass are 90 MPa and 70 MPa, respectively, and the allowable angle of twist of the free end A is 6 degrees, determine the maximum permissible value of T
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
i need the answer quickly