turbo-charge Diesel cycle pv and ts diagram.

Q: Why does the rate of heat release make a peak at the beginning of the Diesel combustion and drop?

A: During the combustion phase in Diesel Engine, air is compressed in the cylinder and into this…

Q: There are supplied 317 Kj/cycle of Diesel engine operating on 227g of air Pi=97.91 KPa, Tı=48.9C. At…

A: You have asked a multi-part question. According to our guidelines, we can provide you the solution…

Q: The working principle of a diesel engine is the Carnot cycle Ture O False O

A: To state whether TRUE or FALSE.

Q: For otto cycle, prove os total >0 MO 20 ?

A: Introduction The Otto cycle, named after Nicolaus August Otto, is a four-stroke cycle used in many…

Q: Briefly describe an ideal reheat Rankine cycle with schematic diagram and T-s plane.

A: Given Data - Topic- Ideal Reheat Rankine Cycle   We have to Explain Reheat rankine cycle with TS…

Q: A diesel engine has an inlet at 95 kPa, 300 K and a compression ratio of 20:1. The combustion…

A:

Q: How many reheat stages possible in Rankine Cycle and why?

A:

Q: Explain the following about steam-mhd with open cycle plant: cool it down - Generation Efficiency -…

A: Magnetohydrodynamic (MHD) power generation is considered an interesting energy conversion system…

Q: In a dual combustion cycle the maximum combustion temperature is 2000degrees Celsius and maximum…

A:

Q: The maximum temperature in : the cycle (in degree Kelvin) is Otto cycle has a compression ratio of…

A: 1) The Maximum cycle temprature =2676.470k OPTION 3 - BETWEEN 2500-2750K 2) The Exhaust temperature…

Q: For a given Tc and TH, the vapor compression cycle has a higher COP than the Carnot cycle. True…

A: COP is the coefficient of performance which indicates efficiency of cycle.  Carnot cycle is a cycle…

Q: Can you please give 3 disadvantages of Reheat Regenerative Cycle?

A:

Q: Question 2 2a. Explain binary cycle power plant (using figure). Compare its performance as…

A:

Q: 4. The efficiency of Diesel cycle approaches to Otto cycle efficiency when a. cut-off is increased…

A:

Q: Q1/ Steam enters the turbine at 30 bar, 400°C, amount of steam is extracted at 5 bar to a single…

A:

Q: How does reheating allow for improved Rankine cycle performance?

A: step by step solution is given below,

Q: Give PV and TS Diagrams of Actual Bryton Cycles. Give also the Work and efficiency equation

A:

Q: 2. An ideal combustion cycle operates on 500g of air. At the beginning of the compression, the air…

A: Given data: r=10rc=1.65α=1.5 Need to determine the efficiency.

Q: Explain inclusion of reheat and modern regenerative arrangement in ideal Rankine cycle to improve…

A:

Q: The thermal efficiency of an actual Rankine cycle is 85%. What is the heat input rate if the net…

A: Rankine cycle is used in steam power plants. Rankine cycle comprises the following process 1)…

Q: miller cycle pv and ts diagram explication

A: The objective of this question is to explain the Pressure-Volume (PV) and Temperature-Entropy (TS)…

Q: There are supplied 320 KJ/cycle of Diesel engine operating on 250 g of air P₁-97.91 KPa, T,-48.9C.…

A: Given data: Here, Qs represents the heat supplied, m represents the mass, P1 represents the…

Q: 1.Give the TS and PV diagrams of Regenerative Rankine Cycle

A: The main components of a Rankine power plant cycle are: Steam turbine Boiler Condenser Pump

Q: at is the final temperature after compression of a diesel cycle if the initial temperature is 30.74…

A: Given:T1=30.74°C=0.08r

Q: What thermodynamic cycle in realised in the internal combustion engines?

A:

Q: Optimum live steam pressure in combined cycle is selected Select one: Oa at maximum rate of waste…

A: optimum live steam pressure in combined cycle e at maximum gas turbine cycle efficiency

Q: A diesel power plant has a super charge engine capacity of 128.15 KW, with 83.5% gen. efficiency,…

A:

Q: How we find the Air to Fuel ratio of Diesel Engine using Single Cylinder Diesel Engine Test Bed with…

A: To conduct the experiment the required equipment is as follows.   1)exhaust gas recirculation…

Q: if isenthalpic process meaning delta H = 0 then why does is there a temperature change across a…

A: This question is based on the concept of Joule Thomson coefficients from thermodynamics.

Q: Draw the schematic diagram for regenerative vapour power cycle with 2 steam blades. Represent the…

A: Sketching the regenerative vapor power cycle with 2 steam blades.

Q: The pressure ratio of a simple air operated Brayton cycle is 12. Air 295 K to the compressor, 1020 K…

A:

Q: Exercise We consider an ideal Diesel cycle whose compressio Xmax osion ratio The heat transfer to…

A: The compression ratio of diesel cycle is The heat addition to the cycle is The initial temperature…

Q: 1. Give atleast 5 Advantages of Reheat Cycle in Thermal Power Plant. 2. Give atleast 5…

A:

Q: The efficiency of a Brayton cycle is 28.5 %. What is the pressure ratio? (assume adiabatic index as…

A: Above cycle in T-S diagram is a brayton cycle which includes 4 processes:- 1-2 → Isentropic…

Q: . An ideal dual com bus tion cycle operates on 454g of air. At the beginning of compression, the air…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Gas turbine is working on Brayton cycle, the pressure ratio in the cycle is 12 and the specific heat…

A: According to the given information, we know that gas turbine is working  on Brayton cycle  The…

Q: An ideal reheat regenerative turbo-generator unit receives 9.0 MPa of throttle steam at 390°C.Reheat…

A: Givnen DataT=390°CP=9MPa

Q: An ideal combustion cycle operates on 500g of air. At the beginning of the  compression, the air is…

A: