true stress of 345 MPa is applied. How much will a specimen of this material elongate when a true stress of 415 A tensile te st is performed on metal specimen and it found that a true plastic strain of 0.02 is produced when a MPa is applied if the original length is 500 mm. Assume that the value of 0.22 for strain hardening exponent.

true stress of 345 MPa is applied. How much will a specimen of this material elongate when a true stress of 415 A tensile te st is performed on metal specimen and it found that a true plastic strain of 0.02 is produced when a MPa is applied if the original length is 500 mm. Assume that the value of 0.22 for strain hardening exponent.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Engineering and true strain
For the curve shown below, calculate the energy required to destroy the specimen. Use any method but your solution must include one integration step at least.
5. A specimen of Al have a cross section 10x12.7 mm², pulled with 35,500N, producing elastic deformation, calculate strain. (Al elastic modulus 69GPA)
C1. A mild steel tensile specimen of initial length 41 mm and initial diameter 6.2 mm is subjected to a tensile test and the following data are obtained. Yield Strength as 115 MPa Maximum Strength as 210 MPa Fracture Strength as 168 MPa Percentage of Elongation as 50 % Percentage of Reduction in area as 32% Determine the Final length, Final area, Yield load, Ultimate load & Fracture load. The yield load in N is The Ultimate load in N is The Fracture load in N is
When the true strain equals 0.14 and the true stress equals 355 MPa, the tensile test specimen starts to neck. Find the strength coefficient and the strain-hardening exponent in the flow curve equation without knowing any more about the test.
2. Consider a cylindrical nickel wire 0.08 in. in diameter and 1200 in. long. Calculate its elongation when a load of 300 N is applied. Assume that the deformation is totally elastic. 3. A cylindrical specimen of a metal alloy 10 mm in diameter is stressed elastically in tension. A force of 3370 Ibr produces a reduction in specimen diameter of 7 x 10* mm. Compute Poisson's ratio for this material if its elastic modulus is 100 GPa. 4. A cylindrical specimen of a hypothetical metal alloy is stressed in compression. If its original and final diameters are 20.000 and 20.025 mm, respectively, and its final length is 74.96 mm, compute its original length if the deformation is totally elastic. The elastic and shear moduli for this alloy are 105 GPa and 39.7 GPa, respectively.
A steel rod is subjected to a force of 5 kN. The initial length of the rod is 690 mm and after elongation its length is equal to 700 mm. Estimate engineering and true strain.
Attempt only if you are sure Urgent.
For some metal alloy, a true stress 345 MPa (50040 psi) produces a plastic true strain of 0.02. How much will a specimen of this material elongate when a true stress of 418 MPa (60630 psi) is applied if the original length is 500 mm (19.69in) ? Assume a value of 0.22 for the strain- hardening exponent, n
Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv)yield strain (v) fracture stress (vi) fracture strain on each graph. You may showboth graphs on one plot. Explain the difference between engineering stress and true stress.
In a micro-Vickers hardness test, the diagonals of the indentation are 54 and 55 um when a load of 200 g was applied to the specimen. Determine the micro-Vickers hardness (HV) of the tested specimen. (Input the answer with two decimal places: like 20.32, 36.26, etc.).
A tensile specimen of cylindrical brass cartridge subjected to a load of 350 kg has a cross section diameter of 3.5 mm and a gage length of 25 mm. Calculate the Young's modulus and engineering strain that occurred during a test if the distance between gage markings is 26.5 mm after the test.