Related questions
Question
1. True or False: If you only want to solve for the forces in just a few truss members and not for the forces in every member of a truss, then using the Method of Sections is more efficient and quicker than using the Method of Joints. True or False? ____________
2. When using the Method of Sections, it recommend that we assume that all members are in____________.
A. Equilibrium
B. Compression
C. Tension
D. Both a. and b.
E. Both a. and c.
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
This is a popular solution
Trending nowThis is a popular solution!
Step by stepSolved in 2 steps
Knowledge Booster
Similar questions
- 6. True or False: When using the Method of Sections, our textbook inform us that, after you split the truss in two, it is always more efficient to first analyze the right-hand side of the truss vs. the left-hand-side of the truss because of the way that our Cartesian Coordinate System is arranged. True or False? ________ 7. A “Simple Truss” consists of a series of ____________ members. A. Single-force Members B. Two-force Members C. Three-force members D. 3D Sections E. Several two-force members with external forces applied at every joint.arrow_forward3. A uniform bar of length 5.00 m is attached by a hinge to a wall (see figure). The bar is held horizontal by a vertical string that exerts a force of 145 N that is applied at a point which is x = 3.33 m from the hinge. Calculate the mass of the bar. a) 44.4 kg b) 22.2 kg c) 19.7 kg d) 4.93 kg e) 9.85 kgarrow_forward2arrow_forward
- Needs Complete typed solution with 100 % accuracy.arrow_forwardBlock A is held in equilibrium when force F = 140 lbf is applied. Each cable is made out of 5-0s gage B & S Non Ferrous Metals wire. Determine the normal stress in each cable and the mass of block A. You may assume the cables and pulleys have negligible mass. C Be A D E Farrow_forward6arrow_forward
- Using the method of joints, determine the force in members AG and FB of the roof truss as shown in Fig. 1. State whether the members (AG and FB) are in tension or compression.arrow_forward2. A 400-N weight is supported by a uniform beam with a mass of 30-kg and a length of 1.6 meters. The beam is connected to a wall through a hinged connection at point C as shown below. If the system is in static equilibrium, draw a free-body diagram and determine; a. The applied tension. b. The reaction forces at the hinge (R. and Ry). 400 N W beam 1.6 m 60° 0.8 m 1.2 m Carrow_forwardNeeds Complete solution with 100 % accuracy don't use chat gpt or ai plz plz plz plz.arrow_forward
- 3. When using the Method of Sections, our textbook recommend that we cut through only _________truss members in order to solve for the forces in a 2D truss when using the Method of Sections. A. 1 B. 2 C. 3 D. 4 E. A possible infinite number of members due to the nature of Vectors. 4. When using the Method of Sections, our textbook informs us that there are ____________ independent equations of equilibrium available when we are using this method to solve for 2D truss problems. A. 1 B. 2 C. 3 D. 4 E. A possible infinite number of equations as well due to the nature of Vectors.arrow_forwardA single non-reinforced concrete column with a rectangular cross-section of 12.0 * 18.0 cm is used to support a large platform a) What is the maximum weight of the platform if we want to maintain a safety factor of at least 10.0? The ultimate compression strength of concrete is 172MPa b)If the column were to break under the weight, where would it most likely break, at the top or bottom?arrow_forward
arrow_back_ios
arrow_forward_ios