True and False (correct the false) 1. In USM, tool tips must have high resistance and fatigue strength. 2. The machinability of USM depends on brittleness criterion. 3. In EDM, negative ions (electrons) collide with positive ions to generate heat. 4. "In EDM, high pressures allow the metal to evaporate." 5. In AJM, corrosion is the mechanism of removal of material from the work piece.

True and False (correct the false) 1. In USM, tool tips must have high resistance and fatigue strength. 2. The machinability of USM depends on brittleness criterion. 3. In EDM, negative ions (electrons) collide with positive ions to generate heat. 4. "In EDM, high pressures allow the metal to evaporate." 5. In AJM, corrosion is the mechanism of removal of material from the work piece.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Discussion : a. Define by what is meant by metallography b. What is the difference between metallography and metallurgy? c. Why must we avoid an increase in temperature in the specimens? d. Why must we rotate the specimen 90° each time between polishing phases. e. How can we avoid the oxidation of the specimen's surface while treating it with etching solution? f. Explain how the etchant solution shows the grains and grain boundary g. Why is the grain boundaries oxidization more sever and are the 1st to be oxidized than the grain surface themselves?
The mechanism of material removal in EDM process is: A) Erosion and Cavitations B) Cavitations and Evaporation C) Melting and Evaporation D) Melting and Corrosion
1. Most common instrument used in the mechanical gages is the dial indicator, which of the following applications cannot be measured by the dial indicator? (a) All of them (b) Perpendicularity (c) Runout (d) Circularity (e) Roughness 2. The main mechanism for the flank wear on the single point cutting tool is: (a) Oxidation wear (b) Adhesion wear (c) None of them (d) Diffusion wear (e) Plastic deformation 3. Higher cutting speeds and temperatures are the main mechanism of the following tool wear mechanism: (a) Diffusion wear (b) Abrasion wear (c) None of them (d) Adhesion wear (e) Plastic Deformation
(a) Figure 1 shows surface roughness and tolerances obtained in Chemical Machining (CM) and Electrochemical Machining (ECM) process for different types of electronic products. Comment on the differences between chemical and electrochemical machining process in terms of surface roughness and tolerance of the machined product as illustrated in Figure 1. 0.9 CM 0.8 0.7 Z ECM 0.6 0.5 0.4 0.3 0.2 0.1 Product A Product B Product C Product D Products 25 E ČM 20 Z ECM 15 10 Product A Product B Product C Product D Products Figure 1: Surface roughness and tolerances of various electronic products Surface roughness, Ra Tolerance, (t mm x 10)
1. The process best in terms of close control of tolerance and surface finish is a. Casting c. Joining e. All of the above b. Forming d. Machining f. None of the above Your answer is: . 2. Castability is poor for: a. High melting point material c. Ductile material b. Low melting point material d. All of the above e. None of the above Your answer is: . 3. The material which can be manufactured by non-conventional method is/are b. Titanium alloy a. Ceramics c. Super alloys d. All of the above e. None of the above Your answer is: . 4. Hand tools like wrenches, spanner etc. are made by the process of a. Casting c. Machining e. None of the above Your answer is: . b. Forging d. Rolling 5. Riser is designed to ensure that molten metal in riser a. Freezes before the casting c. Freezes at the same time as the casting b. Freezes after the casting d. All of the above e. None of the above Your answer is: .
2. In the electrochemical machining of an iron surface with 20 mm× 20 mm in cross-section, the NaCl in water is adopted as electrolyte. The gap between the tool and workpiece is 0.2 mm. The supply voltage is 15 V DC. The specific resistance of the electrolyte is 2 Q cm. (For iron, valency=2, atomic weight=55.85, and density=7860 kg/m³). Please estimate the material removal rate and the tool feedrate.
List 3 different concepts of trenching machine design and modeling. Each concept must have an introduction and design description. Include a photo of each trenching machine design and modeling concept. For Example : an electric trenching machine
a). Briefly explain the anodizing process with a neat diagram. b). Write the application of anodizing process. (minimum 1 and half pages including diagram.)
In EDM, better surface finish is obtained at low frequency and low discharge current low frequency and high discharge current high frequency and low discharge current high frequency and high discharge current
A handwritten solution would be well and good with fbd.
In electroplating, the material to be plated, such as a necklace, acts as the cathode. Select one: True False
3. Electrode This is usually made of graphite, brass, copper and copper tungsten alloys and is needed in electrical-discharge machining to create spark with an electrically charged workpiece. a. Dielectric fluid b. Electrolyte c. Electrode d. Wire 4. Mechanical Which of the following is NOT included in the energy sources utilized in advanced machining. a. Chemical b. Electrical c. Laser d. Mechanical 5. In performing electrochemical machining , the following are necessary in the process except. a. Electrolyte b. Power supply c. Shaped tool d. Dielectric fluid