To, out To, in = 100°℃ OiL m₂ = 0.2kg/s Water > mw=0-15kg L Tw, out Twin- 30°℃ (a) If the outlet temperature of the oil is 60°C, determine the total heat transfer and the outlet temperature of the water. (b) How long must the tube be made if the outlet temperature of the oil is 60°C? (c) Explain and discuss with the use of diagrams the difference between parallel and counter flow heat exchangers? (d)If the heat exchanger is changed to a parallel flow heat exchanger, how long must the tube be made if the outlet temperature of the oil is 60°C?

To, out To, in = 100°℃ OiL m₂ = 0.2kg/s Water > mw=0-15kg L Tw, out Twin- 30°℃ (a) If the outlet temperature of the oil is 60°C, determine the total heat transfer and the outlet temperature of the water. (b) How long must the tube be made if the outlet temperature of the oil is 60°C? (c) Explain and discuss with the use of diagrams the difference between parallel and counter flow heat exchangers? (d)If the heat exchanger is changed to a parallel flow heat exchanger, how long must the tube be made if the outlet temperature of the oil is 60°C?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem -1 A tank is initially empty. A liquid with p = 62.4 Ibm/ft is poured into the tank at a constant mass flow rate of mi = 7 lbm/s. The tank has cross-sectional area A = 0.2 fe, and the fluid in the tank has a %3D variable height H(t). There is a hole at the bottom of the tank. The fluid flows out of the tank at a rate proportional to the fluid height: rme = kH, where k= 1.4 lbm/ft/s. Find H(t). A sketch is given in Fig. P.1. Figure.P.1: Sketch of tank filling problem
a) Calculate the maximum flux the liquid water can have ( η = 0.891 cP and ρ = 0.998 g/mL a 20 ºC) when flowing through a 2 mm diameter tube, in the laminar regime.b) If the pressure when entering the tube is 1 bar, how many meters will it need for the pressure to decrease a 10%? Data: dina/cm3 = 10 Pa/m; 1 bar = 105 Pa. Results: 2.81 cm3/s, 1.57 m
B/A boiling channel receives a thermal power of 6000 kw. If subcooled water at 275 °C enters the channel at a flow rate of 15 kg/s what is the void fraction at the channel outlet where the slip ratio is 1.687 and pressure is 68 bar. Given data: At 68 bar: h=1256 KJ/Kg, hg-1518 KJ/Kg, V-1.344*10-³ m³/Kg, V-28.27*10³ m³/Kg
When passing through an adiabatic turbine (figure), bullet steam at 500 °C and 3.5 MPa expands to 200 °C and 0.3 MPa, it flows at a flow rate of 529 oz/s, what is the power Specified by the turbine in kW if the piping at the same inlet is D1 = 5.90 in diameter and at the outlet, D2 = 0.82 ft in diameter? Data: for steam at initial conditions Hi = 3450.9 kJ/kg at final conditions, H2 = 2865.6 kJ kg; Specific volume of steam in the initial condition = 0.0992 m²/kg; Specific steam volume in the final condition = 0.7163 m/kg. %3! %3D
Q=2000J Tout=? V(m/s) D=0.1m air Air at (2.95x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.5000x10^0) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 100O J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe. Answer should be in 'K' with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: Activate Windows Go to Settings to activat (? 9°C ENG 2020
Q1) Find: (a) inlet temperature (T1 =?), (b) mass flow rate of R-134a ((m =?), (c) exit diameter (D2 =?), (d) the rate of heat transferred to the surroundings (Qout =? ). P2 = 1MPA T, = 70°C Y2 = 70 (- Compressor W in = 100 (W) R-134a P = 500KP. Qout (sat. vapor)(1) m Y1 = 20 ( D = 0.5 (cm)
A centrifugal pump must be installed 6 m above the water level in a tank. the bomb will operate at a rate of 0.01 m³/s. The manufacturer suggests a pump with NPSHR at this flow rate of 2.5 m. Neglect friction losses, with the exception of a heat exchanger between the tube inlet and pump suction, which has a loss coefficient Cf = 15. The pipe diameter is 15 cm and the pressure of water vapor at 30°C is 4.246 kPa. Is this pump suitable for the given conditions?
Air at (2.9000x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.00x10^0) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe.
solve both parts(hand written)
Q:: Flow of hot air through uninsulated square ducts of a heating system in the attic . Determine the exit temperature and the rate of heat loss. Taking k = 0.02953 W/m. C, v= 2.097x10* mis, Pr = 0.7154, kg/m C,=1008 Ans : 75.7 "C , 941.1 W Jkg."C rP = 0.9994 Tom 0mmin
Solve fast and correctly. I will rate.
Q=2000J Tout=? V(m/s) D=0.1m air Air at (3.050x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.50x10^0) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe. Answer should be in 'K' with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible. Your Answer: x10 Answer DELL