To increase the 75 V battery voltage to 100 V, a da-da circuit is required is heard. The converter inductance is 200 μH and the load resistance is 2.2 Ω.Powerswitch has a transmission time of 50 μs and operates in continuous transmission. According to this; d) Find the average value of the input current and the output current. e) Find the minimum and maximum values of the input current. f) Output to be used to limit the fluctuation in the input voltage to 10% of the output voltage.Find the capacity of the circuit.

To increase the 75 V battery voltage to 100 V, a da-da circuit is required is heard. The converter inductance is 200 μH and the load resistance is 2.2 Ω.Powerswitch has a transmission time of 50 μs and operates in continuous transmission. According to this; d) Find the average value of the input current and the output current. e) Find the minimum and maximum values of the input current. f) Output to be used to limit the fluctuation in the input voltage to 10% of the output voltage.Find the capacity of the circuit.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter5: Components, Symbols, And Circuitry Of Air-conditioning Wiring Diagrams

Section: Chapter Questions

Problem 16RQ: Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load...

See similar textbooks

Similar questions

A certain regulator has a percent load regulation of 1%. a) What is the unloaded output voltage if the full load output is 20 V? b) Determine the output waveform. 120 Vrms ooooo ellle A B R surge W 10 Q2 C 100 uF RL 3.3 ΚΩ
Q1/ Sketch the output waveform for the circuit. 15V RL Vo -15V Va 7V Input waveform ww
5) With reference to the circuit diagram given below describe in detail the operation of the circuit diagram with all the applicable waveforms for output voltage, out put current and voltage across the thyristors with alpha=90 degrees Vs = Vo V„ sin wr (a)
A thyristor half-wave controlled converter has a supply voltage of 240V at 50Hz and a load resistance of 100Ω. What are the average values of load voltage and current when the firing delay angle is 30°?
O Inductor Diode Voltage Source Switching Device Capacitor This DC-to-DC converter has a duty cycle of 33.3% and an input of 5V. What is the output voltage if the losses are negligible? LOAD
Single phase full wave controlled converter circuit is powered by a single phase source. When the trigger angle is 0 °, the DC output voltage taken from the output of the converter circuit is 300V. If the trigger angle is 60 °, what is the value of the DC output voltage to be obtained at the output? i have 1 houre
For a Buck converter you need to calculate what range of duty cycles a controller needs to meet the following conditions Input Volatge (from 80V to 120V) DC Needs to output 100V with a 20 Ohm Load The supplied PWN signal is 50 kHz's What is the required range of duty cycles to get the output
please work out the following using the infomation in the attached photo. This is for a Boost converter (a) Output voltage(b) Inductor current ripple (assume it is 20%) (c) Switching frequency (d) Output current (e) Output voltage ripple
7. Given the following linear series voltage regulator calculate the minimum (VOMIN) and maximum (VOMAX) output voltage. Q1 VIN 24V •Vo R2 2.2K R3 10K R4 4.7K R1 Vz 5.1V 4 wwwwww
Calculate and draw the output waveform of the circuit shown below. 5:1 D Da 120 V m Dy Dy ellee
find zener voltage and resistance with given values:capacitor: 470 micro Fresistor: 12 ohmV out: 12V DCI out: 1AV in: 120V AC 60 Hzdiode: 0.7V
Determine the peak value of the output waveform. V-5V 20 V A. 25 V B. 15 V C. -25 V D. -15 V Determine Ioz. D Si 3.3 kn D2 20 V Ge 5.6 kn A. 6.061 mA B. 0.7 mA C. 3.393 mA D. 3.571 mA