Time Delay control system:A level control system. The time delay between the valve adjustment and the fluid output. The flow rate is 5 m³/sec,the cross-sectional area of the pipe is 1 m², and the distance d = 5 m. The loop transfer function is.31.5L(s) =-STe(s + 1) (30s +!) [++ 1]3Find the system gain required to provide the phase margin of 32 °.4020010-1101Magnitude (dB)Phase (deg)ဝိ ဝထိတ်ရင်ဖို့Magnitude (dB)Phase (deg)10-24020-109-122-135-148-161-174-187-2000.50.550.610⁰Frequency (rad/s)0.650.7 0.75 0.8 0.85 0.9Frequency (rad/s)0.951

Answered: Image /qna-images/answer/3185a5b8-4131-4984-bd08-3e01ad62ba88.jpg

Time Delay control system: A level control system. The time delay between the valve adjustment and the fluid output. The flow rate is 5 m³/sec, the cross-sectional area of the pipe is 1 m², and the distance d = 5 m. The loop transfer function is. 31.5 L(s) = -e-st (s + 1) (30s +!)[++ 1] Find the system gain required to provide the phase margin of 32 º. 3 40 20 10-1 101 Magnitude (dB) Phase (deg) O -20 -40 -52 -68 -84 -100 -116 132 -148 -164 -180 -196 -212 -228 -244 -260 10-2 40 Magnitude (dB) 20 O -20 Frequency (rad/s) 10⁰

Time Delay control system: A level control system. The time delay between the valve adjustment and the fluid output. The flow rate is 5 m³/sec, the cross-sectional area of the pipe is 1 m², and the distance d = 5 m. The loop transfer function is. 31.5 L(s) = -e-st (s + 1) (30s +!)[++ 1] Find the system gain required to provide the phase margin of 32 º. 3 40 20 10-1 101 Magnitude (dB) Phase (deg) O -20 -40 -52 -68 -84 -100 -116 132 -148 -164 -180 -196 -212 -228 -244 -260 10-2 40 Magnitude (dB) 20 O -20 Frequency (rad/s) 10⁰

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need the answer quickly
Question 2 Oil (SG = 0.85) is flowing in a 10cm diameter pipe. The elevation of the pipe is 5m above the datum line and the pressure in the pipe is -24KP.. If the discharge in the pipe is 30 L/s, determine the power (in watts) in the stream at that point. A 843.17 Watts B 648.28 Watts (c) 926.41 Watts D No answer among the choices E 716.69 Watts
A siphon is used to drain out a tank of water as shown.The siphon is 3" in diameter and drains out a nozzle of2"-diameter. Determine the flow velocity in the jet.(Hint: Assume a streamline of flow from the water surface, through the siphon and out the jet. Apply Bernoulli's equation on the streamline assuming point 1 at the water surface and point on the jet)
The flow rate of water through the pipe system shown in the figure is 30 lit/s under the total head loss of 10m. Assume C = 120 for all pipes. Determine the diameter of line C in mm.
(67) The water tank shown is filled by pumping water from the well where the water level is located 9 feet below the elevation of the pump. The head added by the pump at a flow rate of 200 gpm is 27 feet. The efficiency of the pump is 85%. The pump power (hp) is most nearly: A. 1.0 В. 1.5 C. 2.0 Tank D. 2.5 15 ft. Pump 9 ft. Well
31 and 32 please :) ill thumbs up
hydraulics fluid flow in closed conduits: pipe networks
5-7E A garden hose attached with a nozzle is used to fill a 20-gal bucket. The inner diameter of the hose is 1 in and it reduces to 0.5 in at the nozzle exit. If the average veloc- ity in the hose is 8 ft/s, determine (a) the volume and mass flow rates of water through the hose, (b) how long it will take to fill the bucket with water, and (c) the average velocity of water at the nozzle exit.
Medium lubricating oil (sg-D0.85) is pumped through 360m of horizontal 75mm pipe at the rate of 3.14L/s. If the drop in pressure is 300kPa. Compute for the absolute viscosity in Ns/m2 of the oil. a. 0.311 b. 0.206 C. 0.504 d. 0.790
Installed is a venturi meter on a pipe 30 cm diameter in which the maximum flow is 2.7 cum of water in one minute. The throat is 15 cm in diameter. Compute the theoretical discharge that would be passing through the meter when the differetial manometer is as shown. Calculate also the discharge coefficient, C.
Given a closed tank with 80mm diam. Orifice at the side. If Cv= 0.45 and Cc=60: A) determine the vertical distance from the orifice that the jet strikes the ground if the horizontal distance of the same point from the orifice is 8.62m B) Find the discharge in lit/sec.
- Dekrmine the total head loss hf. from Å to o in the systen shomwn in the figure iF the discharge is 1. G0 mls. Assume f=0:02 for all pipes 450 mm o, GO0 m 9oomm ở , 90 m 구5Dmmd,40m D GUD mm,720m