Threshold SNR calculation. A certain digital receiver system requires a SNR of -3 dB (power ratio) to be above threshold for proper operation. The system's bandwidth B is 80 kHz and the effective input noise temperature of the system is Tsys=1000 K. What is the minimum signal power PMIN at the system's input needed for the system to operate above threshold? Express your answer in both watts (numeric form) and dBm (dB relative to 1 mW). SYS

Threshold SNR calculation. A certain digital receiver system requires a SNR of -3 dB (power ratio) to be above threshold for proper operation. The system's bandwidth B is 80 kHz and the effective input noise temperature of the system is Tsys=1000 K. What is the minimum signal power PMIN at the system's input needed for the system to operate above threshold? Express your answer in both watts (numeric form) and dBm (dB relative to 1 mW). SYS

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q/why isolator is used in micrpwave bench set up ?
Incremental shaft encoders have usually two pairs of photo emitters and photo detectors. Why is this? 1. Using two pairs of emitters and detectors allows turning an incremental shaftencoder into an absolute one.2. Usually the two emitter/detector pairs are out of phase by an angle of 90 degrees,so that the direction in which the the encoder disk is moving can be determined. Ifthere was only one such emitter/detector pair, the direction could not be determined.3. The additional emitter/detector pair is only introduced, in order to increase theredundancy of the shaft encoder. Hence, if one of them fails, the shaft encoder wouldcontinue operating in the same way as beforehand.4. The additional emitter/detector pair allows measuring additional information aboutthe shaft encoder motion. Whilst shaft encoders with a single emitter/detector paircan strictly only measure the absolute angle of the shaft encoder, adding another pairallows measuring differential speed and acceleration.
3.) What is the meaning of the signal-to-noise ratio for a system, and why is it important?
What are the different types of frequency counter? Define each.
1. The Open Circuit voltage (Voc Rated) of Solar PV module is [greater / lesser]than the Open circuit voltage [Voc Measured]. 2. The Short Circuit Current (Isc Rated) is [greater | lesser] than the Short Circuit Current (Isc measured). 3. What is the effect of clouds on the output of a Solar PV module? O. Focu
Chose the correct answer 7- When does over-modulation occur? a) Modulating signal voltage < carrier voltage b) Modulating signal voltage > carrier voltage c) Modulating signal voltage = carrier voltage d) Modulating signal voltage = 0
2. Consider Figure 1.a) Find and draw an orthonormal basis function set for the signal set given in Figure1a. Apply Gram-Schmidt orthogonalization procedure and show your calculationsteps. Describe the signals in terms of the orthonormal bases. Draw the signalconstellation diagram.b) For Figure 1b, using the orthonormal basis set you derived in Question 2a, describethe signals in terms of the orthonormal bases. Draw the signal constellationdiagram.c) Combine the signal sets in Questions 2a and 2b. You must add another signal setto this combination, so that sum of all the signals ultimately form an efficient 8-QAM modulation scheme. Find and draw this signal set and also describe them interms of the orthonormal bases.
7 Name the circuit shown below? Please justify the name with brief explanation of the working of this circuit. Page 3 of 6 Final Assignment If the input signal is a high frequency input signal to an AM receiver (very less amplitude) will this serve the purpose. If Yes Justify? If NO Justify and give the modification which will make it suitable for the above mentioned purpose. out RL
7- When does over-modulation occur? a) Modulating signal voltage carrier voltage c) Modulating signal voltage = carrier voltage d) Modulating signal voltage = 0
Q2-A-For VCO-LO that represent FM-TX if frequency of the carrier signal at -5 volt. Calculate the frequency deviation Af * signal MESSAGE VT SIGNAL 119 (M) NEGATIVE SUPPLY OSCILLATOR 2v. BUFFER 5 KHz VEC (-12 Vdc) VCO-LO circuit block schematic. (FM) VT [volt] -1 -2 -3 -5 -6 -7 -9 -10 FM Output 500 505 510 515 520 525 530 535 540 545 Freq [kHz] O 10 KHz O O 20 KHz
How to calculate the efficiency in frequency modulation and what is the highest value for efficiency in frequency modulation
What is the problem with AM signal when overmodulation occurs?