Three steel rods (E = 200 GPa) supports a 50 kN load P. Each of the rods AB and CD has a 300 mm2 cross-sectional area and rod EF has a 600 mm2 cross-sectional area. (a) State whether the structure is statically determinate or indeterminate. Why? (b)Determine the force and the stress in each rod. (c)  Determine the deformation of each rod. Note: The link BED is rigid, and BE = ED.

Q: The pin-connectsed structure consists of a rigid bar ABCD and two bronze alloy [E = 100 GPa] bares,…

A: GivenE=100GPaA=340mm2L1=810mmL2=1080mma=480mmb=38mmc=600mmσlim=165MPa

Q: fowe for the reactlon forces if a 40-kN force k appied connection. on the Ateel rod, near andd fow…

A:

Q: Determine the young modulus and the poisson's ratio of this steel.

A:

Q: 3. A tensile force is applied to the I-shaped piece of wood in a testing machine, in the arrangement…

A:

Q: The 0.06R (mm)-diameter bar is made of a brittle material with the ultimate strengths of 0.15R MPa…

A: d=.06R mm where R=993 d=.06×993=59.58 mmσut=.15R Mpa σut=.15×993 Mpa=148.95 Mpa Bending moment and…

Q: The hanger assembly shown is used to suspend equipment from the ceiling. The length of rod AB is LAB…

A:

Q: Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P…

A:

Q: Question 3 Three members of the same material and same cross-sectional area used to support the load…

A:

Q: 1. 2nd A -steel +p=60 kN

A: Given data Aluminum tube AB is fixed on support A, and the load P=60 KN is applied on Steel rod BC…

Q: A rod as shown below is subjected to a tensile force F = 1.1 kN acting at the centroid of two faces.…

A: As the rod is subjected to tensile force, there will be tensile stress on the rod. Tensile stress…

Q: The rigid bar of negligible weight is pinned at o and attached to two vertical rods. Assuming that…

A:

Q: The rigid lever arm is supported by two A-36 steel wires having the same diameter of 4 mm. Determine…

A: According to the given data D=4mm The yield stress of the A 36 steel is 250MPa L=300mm We need to…

Q: Determine the z, y, z components of the moment of reaction at B using scalar notation. Expr

A:

Q: Based on the allowable stress for the bronze, calculate the maximum allowable force that can be…

A:

Q: (6) A ¼-in round wire coiled to form a conical spring with 10 effective coils & an outside diameter…

A: Introduction: Tapered springs are other names for conical springs. Tapered springs offer stability…

Q: force in ns. Consi

A: Given:

Q: B F

A: Lami's theorem: According to this theorem when three forces are acting at a point, then these forces…

Q: A solid brass [E = 98 GPa] axial member is loaded and supported as shown. Segments (1) and (2) each…

A:

Q: A uniform bar 1 is connected to a tapered rod 2. Both are subjected to axial loads as shown. If P =…

A:

Q: steel 2.6. The stiff member AB is horizontal before the load of 5,000 lb is applied at A. The three…

A: Given:The value of the load, The cross-sectional area of the bar ED, The cross-sectional area of the…

Q: B 0.75 m 1.5 m 2 m A = 300 mm? A = 250 mm2 A = 5 mm D E = 200 GPa

A: Given,

Q: A cylindrical hollow shaft shown is subjected to a compressive load acting though its longitudinal…

A: Step 1: Step 2: Step 3: Step 4:

Q: MECHANICS OF DEFORMABLE BODIES 1. In the figure shown, the rigid bar with negligible mass was…

A:

Q: A rigid steel bar is supported by three rods, as shown. There is no strainin the rods before the…

A:

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A1 = 2350 mm2 and an…

A:

Q: he structure shown below consists of an arch AB and an elastic column BC. (Note: Joints where…

A:

Q: 3. A load Q is applied at joint B of a structure of three bars of equal axial rigidity AE, as shown.…

A: This issue is from subject of Solid Mechanics Castigliano's hypothesis: It expresses that assuming…

Q: of d₂ = 0.75in. Aluminum e aluminum is 40 ksi. Assu fely be applied to the stru

A: BronzeE1=15000ksid1=0.60inYield-strength=48ksiAluminiumE2=10000ksid2=0.75ind3=1.00inYield-strength=4…

Q: Two solid bars support a load Pas shown. Bar (1) has a cross-sectional area of A1 = 2600 mm2 and an…

A:

Q: 1.5 m 3 m 400 N 200 N 1 m Member AB is supported by a cable BC and at A by a square rod which fits…

A: Given data: F1=200 NF2=400 NuBC=-0.857i+0.429j+0.286k Need to determine the tension in the cable.

Q: A uniform bar of weight 500N is held in horizontal position by 3 vertical wires as shown. Diameter…

A:

Q: An aluminum column with a length of L and a rectangular cross-section has a fixed end B and supports…

A: Given-Information: L=20inchE=10.1×106psiP=5kipsFOS=2.5 To-Determine: (a) The ratio a/b of the two…

Q: A round column 1.5 m long is pinned on both ends carry a maximum compression load of 88 K (critical…

A:

Q: 3. Two columns A C and BC have a circular cross section of radius 5 cm, yield strength oY=100 MPa,…

A: Given: Load P=100kN Diameter of the links=0.05×2=0.1m E=100GPa

Q: Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has…

A:

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.