Three reservoirs 1, 2, & 3 have elevations 322 m, 306 m, and 272 m respectively. The 3 pipes have the properties tabulated below: Pipe 1 Pipe 2 Pipe 3 Length, m 800 700 900 Diameter mm 400 300 350 friction factor 0.022 0.02 0.019 Determine the discharge in each pipe.

Three reservoirs 1, 2, & 3 have elevations 322 m, 306 m, and 272 m respectively. The 3 pipes have the properties tabulated below: Pipe 1 Pipe 2 Pipe 3 Length, m 800 700 900 Diameter mm 400 300 350 friction factor 0.022 0.02 0.019 Determine the discharge in each pipe.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2. Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a…

Q: QUESTIONS: 1) ZB в A Zp V D Figure 1 The physical characteristics of the pipes are seen in the Table…

A: Apply energy between AC and BC and between AD and BD

Q: Water flows at a rate of 0.05 m³/s from reservoir A to reservoir B through three concrete pipes…

Q: Piezometric tubes are tapped into a pipe section as shown in the figure below. The liquid is…

Q: Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the…

A: The answer is found to be Difference in level of two tank = 7.6 cm For explanation please refer the…

Q: 2. Compute the rate of flow in a pipe with diameter300 mm for a length of 900 meter having a head…

Q: Question 2 Refer to Figure 2 below. If the water surface elevation in reservoir B is 110 m, what…

Q: Two pipes are connected in parallel between two reservoirs A and B. The diameter, length Statement…

A: Dia of pipe 1 = 10 cmLength of pipe 1 = 1000 mCoefficient of friction for pipe 1 = 0.02Dia of pipe 2…

Q: Current Attempt in Progress Determine the elevation difference, Ah, between the water levels in the…

A: So,Using pressure equation between both tanksPA-γwh+Sγw0.4+γwh-0..4+γwΔh=PBTaking PA=PB=PAtm=0

Q: When the three reservoirs are connected by a pipeline as shown in the following figure, (1) use the…

A: z1 - hf1 = z2 - hf2 and z2 - hf21 = z3 - hf3 80 - hf1 = 100 - hf2 and 100 - hf2 = 70 -…

Q: Your assigned problem: If the water surface elevation in reservoir B is 110m, what must be the water…

Q: The elevations of water surfaces in reservoirs A and B are 300 ft and 250 ft, respectively, and…

A: g =9.81m/s2 = 32.185 ft/s2 Q1 = 50ft3/s

Q: A confined aquifer underlies an unconfined aquifer as shown in the illustration below. Given the…

Q: Estimate the uplift pressure under bottom left corner of this dam If the entire dam sits 2ft below…

A: coefficient of permeability, Height, Height,

Q: what power must the pump supply in HP to allow this flow?

A: Given:- Discharge, Q=0.35 m3/sHead loss is equal to twice velocity head in 30 cm pipe To find:-…

Q: Two discharge wells (1 and 2) penetrating a confined aquifer are pumped at constant rates of 2572 m…

A: step 1-

Q: Hydraulics equation

Q: There are three pipes and each has different friction or roughness factors below: Saint Pancras…

Q: In a three reservoir problem, the elevation of reservoir 1 and 2 are 462 m and 368 m respectively.…

A: Consider the following diagram:

Q: m 2. Find the maximum amount of w n be pumped from the well in an aqu /day and S = 8 x 10-³ in order…

A: Jfjgpjg gigg jihohohohoghihohohoh Hobobohoh

Q: Reservoir 1 = In figure, if L1= 20 m, diameter 30 cm, velocity = 0.1 m/s, friction ?= factor= 0.023,…

Q: A well is installed in a unconfined aquifer. Determine the drawdown (ft) at the well if: the radius…

A: R=500ft H=95ft

Q: Three pipes 1, 2 and 3 from three reservoirs A,B and C, respectively, meet at a junction whose…

A: Given:- Pipe 1 Pipe 2 Pipe 3 A-J…

Q: A 150 mm diameter pipe 60 m long connects two reservoirs. Determine the difference in elevation…

A: To Determine The difference in elevation between the water surfaces of the two reservoirs, hL

Q: Determine the water flow rate of hydraulic system shown in Fig. (neglected the . minor losses) $00…

Q: SITUATION #2c: Three pipes 1, 2, and 3 from three reservoirs A, B, and C, respectively, meet at a…

Q: A series of three parallel pipes connect the bottom of two reservoirs. All pipes are made of the…

Q: The three-reservoir system is shown below: A A 2 1 3 C The elevation of Reservoir at A is 140m and…

Q: The three water-filled tanks shown are connected by pipes as indicated. If minor losses are…

A: Pipe 1: Elevation: Diameter of pipe: Length of pipe: Friction coefficient: Pipe 2: Elevation:…

Q: A cylinder of cross- sectional area 3500 mm is filled with sand of Overfow permeability 6 mm/s.…

A: Solution Given Data Cross-sectional area= 3500 mm2 Permeability= 6 mm/s

Q: Reservoirs A and D are connected by a pipeline system as shown below. The water surface elevations…

A: Given, Surface elevation of reservoir A = 100 ft Surface elevation of reservoir B = 80 ft

Q: Current Attempt in Progress Determine the elevation difference, Ah, between the water levels in the…

Q: The figure shown below is a siphon discharging oil (s=0.9). The siphon is composed of 8 cm pipe from…

A: step 1-

Q: Determine the pressure difference ?????? ?????−???? ?????= ?(kPa) between the two pipelines.

Q: Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the…

Q: Determine the flow in each pipe in the reservoir shown below. Use the values provided in the table.…

A: To Determine the flow in each pipe in the reservoir shown.

Q: Situation 2: Reservoir B in the figure supplies 560 liters per second to reservoirs A and C. For…

A: Given data: pipe 1 D=600 mm L=500 m pipe 2 D=800 mm L=800 m pipe 3 D=400 mm L=800 m f=0.025…

Q: Piezometer Reservoir A Elevation 100 ft Reservoir C Elevation 80 ft Reservoir B Elevation 80 t…

A: Given that, Hazen William's equation with C1=120. Using Hazen William's equation velocity…

Question

Three reservoirs 1, 2, & 3 have elevations 322 m, 306 m, and 272 m respectively. The 3 pipes have the properties
tabulated below:
Pipe 1
Pipe 2
Pipe 3
Length, m
800
700
900
Diameter mm
400
300
350
friction factor
0.022
0.02
0.019
Determine the discharge in each pipe.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2.38. Reservoirs A, B, and C are connected as shown in Figure 2.28. The water elevations in reservoirs A, B, and C are 100 m, 80 m, and 60 m, respectively. The three pipes connecting the reservoirs meet at the junction J, with pipe AJ being 900 m long, BJ 800 m long, CJ 700 m long, and the diameter of all pipes equal to 850 mm. If all pipes are made of ductile iron and the water temperature is 20°C, find the flow into or out of each reservoir. Elev. 100 m Elev. 80 m A LAJ = 900 m LBJ = 800 m Elev. 60 m Ljc = 700 m FIGURE 2.28: Connected reservoirs
find the discharges in each of the pipes for the following pipe network configuration Given data L = 200 m D = 4cm f = 0.05 15 cumec A E B D с 15 cumec
please answer with complete solution and explanation
Problem4
Determine the elevation difference, Ah, between the water levels in the two open tanks shown in the figure below. Assume SG = 0.89. 1m Ah = SG. Water 0.4 m ↑ V 3 Ah
Explain and give complete solution and clear
Two reservoirs are connected by two parallel pipes of equal length and of diameters 20 cm and 10 cm, as shown in the figure (not drawn to scale). When the difference in the water levels of the reservoirs is 5 m, the ratio of discharge in the larger diameter pipe to the discharge in the smaller diameter pipe is (Round off to two decimal places) (Consider only loss due to friction and neglect all other losses. Assume the friction factor to be the same for both the pipes) ! Reservoir 5 m 20 cm 10 cm ļ Reservoir
Two reservoirs are connected by two parallel pipes of equal length and of diameters 20 cm and 10 cm, as shown in the figure (not drawn to scale). When the difference in the water levels of the reservoirs is 5 m, the ratio of discharge in the larger diameter pipe to the discharge in the smaller diameter pipe is (Round off to two decimal places) (Consider only loss due to friction and neglect all other losses. Assume the friction factor to be the same for both the pipes) ! Reservoir 5 m 20 cm 10 cm ļ Reservoir
Find the discharges in pipes 1, 2, and 3 in the reservoir system shown. The junction loss occurs for both flow from 1 to 3 or from 2 to 3. 50 m D; =0.3m L = 200m 20 m & =1mm D =0.5m 4=500m 4=1 mm p=999.1kg/m u=0.001139 kg / ms K=0.5 Kes =1 D=0.9m L =800 m Jnction Om 6=1mm
pls do not round off the decimal. only in the final answer
Three reservoirs A, B and C are connected by a pipe system shown in the figure below. If the rate of flow from the reservoir A is 55 l's, and the coefficient of friction (F) for all pipes is 0.015. Find the piezometric head at point D A L2=600 m d2=20 cm D Q1=0.055 m/s L1=1200 m d1=30 cm 28 m 30 m
b3