Three-Phase System Three loads are connected in parallel to a 12.47 kV, 60 Hz three-phase supply. Load 1: Inductive load, 60 kW and 660 KVAR Load 2: Capacitive load, 240 kW at 0.8 . power factor Load 3: Resistive load 60 kW Define: a. Active power, reactive power and total apparent power? b. Total power factor ? c. What is the total supply current?

Three-Phase System Three loads are connected in parallel to a 12.47 kV, 60 Hz three-phase supply. Load 1: Inductive load, 60 kW and 660 KVAR Load 2: Capacitive load, 240 kW at 0.8 . power factor Load 3: Resistive load 60 kW Define: a. Active power, reactive power and total apparent power? b. Total power factor ? c. What is the total supply current?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Similar questions

)Two complex loads Z1 and Z2 are connected in parallel and powered by a value voltage effective 7.2 kV and frequency 60 Hz. The first load has a power of 50 kVA and a factor of rear power of 0.9. The second charge has a power of 45 kW and a rear power factorof 0.91. Determine in steady state the kVAR power and the capacity required to correct the Total power factor to a value of 0.97 rear.
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three-phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT
The circuit shows an unbalanced electrical installation powered by a positive sequence symmetrical three- phase network of 380 V compound voltage. The loads are single phase. Load 1 absorbs an active power of 950 W with f.d.p. 0.5 inductive. Load 2 absorbs an active power of 1,140 W with f.d.p. Unit. Load 3 absorbs from the network an active power of 760 W with f.d.p. 0.5 capacitive. Taking the network voltage URN as the phase reference, calculate: a) complex expressions of the line currents IR. Is. and IT RO- SO TO IR Is IT U₁-380 V CARGA 1 P₁ =950 W cos p1=0,5 ind. CARGA 2 P₂=1.140 W cos p₂=1 CARGA 3 P3=760 W cos p3=0,5 cap.
There is an installation with two equal triphasic loads of 300 kVA each and a power factor of 0.9 lagging. When connecting a pure reactive element in parallel, the reactive power at the entrance of the installation is 150 kVARS, with a lagging power factor. We can say that: a) A bank of reactors was connected and the fp deteriorated. b) A capacitor bank was connected and the pf deteriorated. c) A bank of reactors was connected and the fp improved. d) A capacitor bank was connected and the pf improved. e) None of the above
A three phase load has a rating of 200 KW, 4000 volts, 0.7 power factor lagging and a frequency of 50 Hz. Determine the required capacitor bank rating in micro Farad per phase to improve its power factor to 0.9 lagging if: a) The capacitor bank is to be connected in Delta. b) The capacitor bank is to be connected in Star.
Consider a 10 kVA, 200/400 V, 50 HZ: single-phase tranformer has the folloving test results:0.C. test: 200 V, 0.6A, 63 W (L.V.side)S.C. test : 20 V, 25A, 85 W (H.V. side)Deternine:i- The eficiengy at 75 % offiull-load at 0.9 leading power factor.ii -The secondary terminal voltage on fill-load at tunity power facton
A load has a leading power factor. a) Is it a capacitive or inductive load? b) Is the reactive power positive or negative? c) Repeat for a load with lagging power factor
1980628cmid 11616 For reactive load, the power factor is equal to Select one: O a. 1 O b. 90 O c. 2 O d.0 If the voltage V, = 800 mV, then the current flowing in the primary winding Ip is: j2on Select one: O a. None of these O b. l, =40<0° mA O c.l, = 0.320<90° A O d. Ip =320<-90° mA if a Load absorbs an average power of 8 kW at a lagging power factor of 0.5 Select one: O a. -8000 + j13856.4 VA O b. None of these O c. 8000 - j13856.4 VA O d. 8000 - j13856.4 VA estion-299141-3 freactive power is
Consider the circuit shown. Find the following: a. Total load impedance seen by the voltage source. b. Complex power delivered by the source. c. Average power delivered by the source. d. Reactive power delivered by the source. e. Load power factor and power factor angle.
If the load is connected to the generator thgrough an inductive line and the voltage at the load side is the same as the voltage at the terminals of the generator, which of the following must be true? O A. The reactive power is flowing from the generator to the load and from load to the generator at the same time. O B. The load is disconnected, and no power is delivered to the load. O C. The load has a poor power factor and it's absorbing too much reactive power. O D. None of the other choices are correct O E. The generator is unable to produce reactive power; therefore, the reactive power is flowing from the load to the generator.
In an installation there is a three-phase load of 300 kVA with a power factor of 0.8 behind, in parallel with a three-phase load of 150 kVA with a power factor of 0.6 ahead. A pure reactive element is connected in parallel, and a unity power factor is obtained at the power input. Indicate the reactant of the element, with a positive sign if it is a bank of reactors, or with a negative sign if it is a bank of capacitors. Just put the corresponding sign followed by the numerical value, without units. The numerical value must correspond to the three-phase kVARS. You can use integer values with no decimal places or up to two decimal places
In an installation there is a three-phase load of 300 kVA with a power factor of 0.8 behind, in parallel with a three-phase load of 150 kVA with a power factor of 0.6 ahead. A pure reactive element is connected in parallel, and a unity power factor is obtained at the power input. Indicate the reactant of the element, with a positive sign if it is a bank of reactors, or with a negative sign if it is a bank of capacitors. Just put the corresponding sign followed by the numerical value, without units. The numerical value must correspond to the three-phase kVARS. You can use integer values with no decimal places or up to two decimal places