This motor has a series-field winding of 15 turns per pole. Its armature resistance in RA=0.05 22, and its series field resistance is Rs = 0.05 92. The magnetization curve at 1800 RPM is given by the following table: EA (V) F (Amp.turns) 50 95 125 150 180 200 212 229 243 250 253 200 500 755 1000 1280 1500 2000 2500 3000 3500 4000 The motor is operating at rated voltage, armature current of 100 Amperes, and with rotational losses of 1500 Watt. Find the speed of the motor. Answer: The speed of rotation is: RPM

This motor has a series-field winding of 15 turns per pole. Its armature resistance in RA=0.05 22, and its series field resistance is Rs = 0.05 92. The magnetization curve at 1800 RPM is given by the following table: EA (V) F (Amp.turns) 50 95 125 150 180 200 212 229 243 250 253 200 500 755 1000 1280 1500 2000 2500 3000 3500 4000 The motor is operating at rated voltage, armature current of 100 Amperes, and with rotational losses of 1500 Watt. Find the speed of the motor. Answer: The speed of rotation is: RPM

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The relation between armature torque and armature current of a DC motor is Parabolic Linear Inverse Exponential
QUESTION 2 a) Draw the equivalent circuit and torque-speed characteristic curve for a series DC motor. b) Briefly explain the induced torque occurs in a series DC motor. e) A 20-hp 240-V 76-A 900 rimin series motor has a field winding of 33 turns per pole. Its armature resistance is 0.09 2, and its field resistance is 0.06 2. The magnetization curve expressed in terms of magnetomotive force versus Ex at 900 rimin is given by the following table: Table Q2 c): The magnetomotive force table for a de motor taken at 900r'min E. V 95 150 188 212 229 243 F.A tuus 1000 1500 2000 2500 500 3000 If the motor running at 33 percent of the full-koad armature current, determine: ) The motor's power converted from electrical to mechanical form, Prene i) The motor's torque, Tnit ii) The motor's speed, n
A 35.2 HP, 250 V, 100 A, 1200 RPM, series DC motor with no armature reaction is considered in this problem. This motor has a series-field winding of 5 turns per pole. Its armature resistance in RA =0.05 ohm, and its series field resistance is Rs =0.05 ohm. The magnetizationcurve at 1200 RPM is given by the following table:
The schematic and torque-speed characteristics of a series wound DC motor are shown below : Field winding DC Supply Eb speed Torque - T-K, I, Field Flux = ø = Kla (i) According to the equations given above, explain why the torque of the series-wound DC motor is so high at low speed. Give application examples that require such torque-speed characteristics. A series-wound DC motor should never be started with light or NO LOAD. Give reason. (ii) (iii) Armature anbio
A universal motor has armature circuit resistance of 15 ohm and inductanceof 0.3H. On being connected to a 220 V dc supply, it draws 1.5 A from themains and runs at 2000 rpm. Find the speed and power factor of the motor,when connected to a 230 V, 25 Hz supply and drawing the same armaturecurrent.
the relation between armature and field currents in a series connected DC motor is O It = If + la O It=la - If O If = la
A triplex lap wound armature has 300 turns and takes 125 A of armature current. The flux per pole is 20 mWb and the 2-pole series DC motor has a rated speed of 480 rpm with rotational losses of 700 W. Solve for back emf (V)
16 A 4-pole dc series motor has wave connected winding with 600 conductors. When fed from 250 V dc source, the motor drives a load of 5 kW and takes 50 A with a flux per pole of 10 mWb. The torque developed is (Neglect losses).
A 4 pole, 250 dc shunt motor has a lap connected armature with 960 conductors. The flux per pole is 2 x 10-2Wb. Calculate the torque developed by the armature and the useful torque in N-m when the current taken by the motor is 30A. The armature resistance is 0.12 ohm and the field resistance is 125ohm. The rotational losses amount to 825W
Examine the saddle torque of induction motors and the effect of different groove structures on the saddle torque.
8) A 230 V fed single quadrant chopper has a 40% duty cycle. A separately excited DC motor is controlled by a chopper. Motor has a back emf constant of 0.5 V/rad/s and 2 22 armature resistance. Determine the torque of motor at speed of 1400 rpm 4.7 N-m 15.44 N-m 10.5 N-m 19 N-m
A 250-V, 4-pole, wave-wound DC series motor has 782 conductors on its armature. It has armature, diverter and series field resistance of 0.15 ohm, 0.02 and 0.05 respectively. The motor takes a current of 40 A. Estimate its speed if it has a flux per pole of 25 mWb.