There are 5005 electrons in an assembly. What will be total charge in coloumb?

Q: A 1-m length of tungsten wire draws 5 A when connected across a battery. The wire is then cut into…

A: The tungsten wire will have resistance, the above circuit can be thought of as if a battery is…

Q: Determine the Norton equivalent current IN and resistance RN across terminals a – b. - 0.01v, R V…

A:

Q: IND THE POWER IN THE RL CHARGE AND IN THE D1 DIODE - Using thevenin or Norton theorem - Please,…

A: The given circuit diagram is shown below.We need to determine the power in the RL charge and the…

Q: The figure4 shows the relation between resistance and temperature for the thermistor.…

A:

Q: If a small power system has a  base power of 5.0 MVA and base current is 1000 A, the base voltage…

A: Given: Base power =5MVA Base current= 1000 Formula used: P=VI

Q: As the doping of a pure semiconductor is increased the resistance will Answer:

A: For a pure semiconductor if doping is increased, either free holes or electrons are created. These…

Q: he figure the current in resistance 6 is ig = 1.36 A and the resistances are R1 = R2 = R3 = 2.50 N,…

A: The solution can be achieved as follows.

Q: Question 7 Semiconductors has number of valence electrons.

A:

Q: Mame and describe three3) Speci FiC Purpose InPyt devices people communits 45ed In The Public Places…

A: Name and describe three special-purpose input devices  people commonly use

Q: A single cell battery “A” is charged using double-cell battery “B” which is charged using a…

A: These are batteries that can be re-energized by streaming current in the converse manner through the…

Q: What will be the total charge of an assembly of 12389 electrons?

A: The charge on a single electron is,

Q: If V1 = 22 V, V2 = -7 V, R1 = 1.2 kOhm, R2 = 4.7 kOhm, R3 = 2.4 kOhm, and all diodes are silicon for…

A:

Q: The diodes in the circuit are all Silicon with forward voltage of 0.7 V. If R1 = 60 and R2 = 140,…

A:

Q: If we use 5000 µF, we can get a very low ripple voltage. But this is so bad and this a disadvantage,…

A: According to the given question we are using a 5000 micro farads capacitance , then there is a…

Q: Find the current through the diode in mA.

A:

Q: 16 Determine the current at LED, D2. (assume LED forward voltage is 2.1 volts) * R2 1K 5V D1 R1 D2

A: The solution is given below

Q: 2. Analyze and determine the Leq for the circuits in Figure 1 (a) and (b). L m L L Lea m ell ell L…

A: In this question we need to find a equivalent inductance of the given circuit

Q: Ž Rs= 0,25 k Powerd, -? y0z=0,3V Power De=? 20v 0,15 kR

A:

Q: Calculate the resistance between the two corners of the same edge.

A:

Q: Draw the voltage tripler circuit and explain its operation. Explain the difference between voltage…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: 2B/ Al has energy gap of 0 ev, AIN has energy gap of 6.3 ev, GaSi has energy gap of 1.95 ev Classify…

A:

Q: Problema 6 In the figure, the current Ibat in the battery is equal to A. 1/2 B. 21₁/3 C. I₁ D. 31/2…

A:

Q: BATTERY (11) 3 BT1 DIODE D? DIODE D1

A: For this Circuit we need to calculate voltage drop across the resistance R1BT1=13.6…

Q: For the following circuit find VL, IL, Iz and IR if RL = 180 , repeat for R₁ = 470 R$ 20 V 220 2 Vz=…

A: Given: Circuit diagram,

Q: Figure 3 + 6 V 10 kM 20 kn 20 kn

A: To find the output voltage of a circuit that contains a diode, it is important to find the on/off…

Q: Rectifier Circuit for nos. 1 to 7. Determine the reading of each meter and PLave. 220V 1k V2 V3

A:

Q: Can you explain part (b), how did you write the solution

A: It was answered using fourier transform properties.  Property used here is frequency shifting.

Q: In an n-type semiconductor material, the net flow of charge will be the flow of Blank 1. Blank 1 Add…

A: 1) n-type semiconductor material  2) if more impurities are added in the semiconductors, then their…

Q: In this lab, you will be using resistors of various nominal values. What are the 5-band colour codes…

A: Given resistor values are: 100 Ohm220 Ohm 390 Ohm 560 Ohm 1000 Ohm

Q: 6 volts are applied along a 2-cm-long semiconductor bar. The average drag speed is 104 cm/sec. What…

A: Drift velocity is given as                               ϑd=µE where µ is the mobility of an…

Q: 1. Two identical zinc-carbon batteries are available. When connected in series, they supply 0.5…

A: The basic problem on battery is solved here

Q: Which of the following has higher energy? a. valance band electrons b. impurity atoms c.…

A: The above question is related to the subject of Electronics Devices To get the answer of the above…

Q: List out any two advantages of thermistor.

A: Advantages of thermistor: 1. If the temperature of any component in the electrical circuit…

Q: 10V 1A 4A Ib 122 + 8V Figure Q1(b)

A:

Q: When a pure semiconductor is heated, it's resistance: a) goes down. B)changing every time. C) goes…

A: In this answer let us try to understand what happens to the resistance of a semi conductor when it…

Q: I currents. +3 V +3 V 5 kn 10 kM Z D Z D. IZ D, SZ D.

A: As per Bartleby policy we can answer only one part at a time so i am solving a part, repost for…

Q: For the network shown in Figure B22 , assume E = 17V,Diode D1, D2 as Germanium Ri-2KΩ and R-3ΚΩ.…

A: Fig: Given circuit

Q: Rea Each resistor is 100 2 (a)

A: Here there are combinations of resistors. We have to use the basic methods of simplification of…

Digital Integrated Circuit Design

Digital IC design is a procedural interaction that involves converting determinations and highlights into computerized blocks, which are then further transformed into basic circuits. A significant number of the imperatives related with advanced IC plan come from the foundry cycle and innovative restrictions.