The worker shown below is driving 4 screws into a panel with a powered driver. His production quota is 2,300 panels per 8-h shift. What specific ergonomic problems are found on this job? For each problem: (a) specify an ergonomics improvement that would correct the problem and (b) provide a specific design principle to support this methods change. Problem Neck flexion Shoulder abduction Ulnar deviation Trigger finger Standing posture Ergonomics Improvement tilt panel up lower work surface to elbow rest height use 3-finger trigger to minimize stress on one part Design Principle Principle 2 of workplace design: Adjust the worl surface height based on the task being performed re-orient panel, or pistol- Principle 3&4 of tool design: Perform twisting motions with the elbows bent & Maintain a grip tool straight wrist sit/stand stool to alternate postures Principle 1 of workplace design: Determine wor surface height by elbow height Principle 5 of tool design: Avoid tissue compression Principle 5 of workplace design: Encourage postural flexibility

The worker shown below is driving 4 screws into a panel with a powered driver. His production quota is 2,300 panels per 8-h shift. What specific ergonomic problems are found on this job? For each problem: (a) specify an ergonomics improvement that would correct the problem and (b) provide a specific design principle to support this methods change. Problem Neck flexion Shoulder abduction Ulnar deviation Trigger finger Standing posture Ergonomics Improvement tilt panel up lower work surface to elbow rest height use 3-finger trigger to minimize stress on one part Design Principle Principle 2 of workplace design: Adjust the worl surface height based on the task being performed re-orient panel, or pistol- Principle 3&4 of tool design: Perform twisting motions with the elbows bent & Maintain a grip tool straight wrist sit/stand stool to alternate postures Principle 1 of workplace design: Determine wor surface height by elbow height Principle 5 of tool design: Avoid tissue compression Principle 5 of workplace design: Encourage postural flexibility

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I need problems 6 and 7 solved. I got it solved on 2 different occasions and it is not worded correctly. NOTE: Problem 1 is an example of how it should be answered. Below are 2 seperate links to same question asked and once again it was not answered correctly. 1. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857 2. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/bd5390f0-3eb6-41ff-81e2-8675809dfab1
I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the example shows on problem number 1. Here is the link to the questions I already had answered, could you please rewrite the answer so its properly answered as the example shows (Problem 1)? https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857
Example: Thesis Statement (1) Check () the thesis statements that suggest a chronological order. Put a double check (V) next to the thesis statements that suggest the essay will describe a process or procedure. In the sentences you have checked, circle the word or words that indicate chronological order or process. к1. A child learns to handle responsibility in a series of small steps. X2. 3. WA. 5. X6. X7. X8. 9. A person's intelligence is the product of both heredity' and environment. There are two main reasons I believe women in the army should not be allowed in a war zone along with men. The procedure for submitting expense reports has recently changed. The tensions that led to last year's student riots had been developing for several years. North American directness often conflicts with Asian modesty. The two busiest travel days in the United States are the Wednesday before and the Sunday after Thanksgiving. Cultures celebrate the end of winter and the arrival of spring in…
A Team of Engineers asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report to show your approach in solving and discussing the following tasks and issues. You must follow the following steps to help the team: STEP 1 Describe the operational sequence of four-stroke spark ignition and four-stroke compression ignition engines with the aid of sketches by constructing simple sketch representing the operation and plotting the P-V diagrams for each process during the cycle to show the following: The input and output heat and net output work The air-fuel mixture intake and exhaust gasses The spark plug when it is in the active mode
Problem 3: Insulation To=1 Toowwww Steam Tx2 T₂ T3 www www R₁ R₁ R₂ www.T R₂ Steam at T1 = 320 °C flows in a cast iron pipe (k= 80 W/m. °C) whose inner and outer diameters are 5 cm = 0.05 m and D₂ = 5.5 cm = 0.055 m, respectively. The pipe is covered with 3-cm-thick glass wool insulation with k = 0.05 W/m. °C. Heat is lost to surroundings at T2 = 5 °C by natural convection and radiation, with a combined heat transfer coefficient of h₂ = 18 W/m². °C. Taking the heat transfer coefficient inside the pipe to be h₁ = 60 W/m². °C, determine the temperature drops across the pipe and the insulation. The determination is based on a unit length of the pipe (L = 1 m). Assumptions 1. Heat transfer is one-dimensional since there is no indication of any change with time. 2. Heat transfer is one-dimensional since there is thermal symmetry about the centreline and no variation in the axial direction. 3. Thermal conductivities are constant. 4. The thermal contact resistant at the interface is…
A Team of Engineers asked for an internal combustion engine to use it in a designed car. Your role is to describe the operation sequence of different types of available engines, explain their mechanical efficiency, and deliver a detailed technical report to show your approach in solving and discussing the following tasks and issues. You must follow the following steps to help the team: STEP 1 Describe the operational sequence of four-stroke spark ignition and four-stroke compression ignition engines with the aid of sketches by constructing simple sketch representing the operation and plotting the P-V diagrams for each process during the cycle to show the following: The input and output heat and net output work The expansion and compression strokes The air-fuel mixture intake and exhaust gasses The spark plug when it is in the active mode The complete cycle of ideal Otto and Diesel cycles that shows the input and output heat and net output work. STEP 2 Explain the mechanical…
You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…
This is an engineering problem and not a writing assignment. Please Do Not Reject. I had other engineering tutors on bartleby help me with problems similar to this one. This problem must be presented in a logical order showing the necessary steps used to arrive at an answer. Each homework problem should have the following items unless otherwise stated in the problem: a. Known: State briefly what is known about the problem. b. Schematic: Draw a schematic of the physical system or control volume. c. Assumptions: List all necessary assumptions used to complete the problem. d. Properties: Identify the source of property values not given to you in the problem. Most sources will be from a table in the textbook (i.e. Table A-4). e. Find: State what must be found. f. Analysis: Start your analysis with any necessary equations. Develop your analysis as completely as possible before inserting values and performing the calculations. Draw a box around your answers and include units and follow an…
PROBLEM SET # 7: THE EQUILIBRIUM MODEL On the space provided, present correct and organized solutions to the following answered problems. Box the final answers. Detach each page neatly and submit to your instructor. 1. A Christmas light hangs on a series of strings as shown in the figure below. The tension on string a, Ta, is 0.48 N. %3D 42° b. J a C 30° 25° 비 m (a) What is the tension on string b? (Ans: 0.22 N) (b) What is the tension on string c? (Ans: 0.35 N) (c) What is the tension on string d? (Ans: 0.37 N) (d) What is the mass of the Christmas light, m, in grams? (Ans: 34 grams)
Learning Goal: To use fundamental geometric and statics methods to determine the state of plane stress at the point on an element of material that is rotated clockwise through an angle from the in- plane stress representation of the point. The state of in-plane stress at a point on an element of material is shown. Let o, the same point that is rotated through an angle of 0-35 45.0 ksi, o, 19.0 ksi, and Ty 12.0 kai. Use this information to represent the state of stress of
Part 2 Set up a spreadsheet solution to this problem. This will require that you derive one formula to express the relationship between the friction coefficient, the spring constant, and the spring compression; and a second formula to find the cost of using different slide and spring types. Set up your spreadsheet as shown below. You can fill in the "Acceptable?" column manually, rather than using a formula. Turn in a copy of your spreadsheet/Matlab work (solve for $) Friction Spring Constant Spring Compression M k 0.1 0.1 0.1 0.2 0.2 0.2 50 100 150 50 100 150 4 Part 3 Your boss has decided to look at a second option. The spring mechanism will be replaced by a drop box. After leaving the slide, the blocks will travel 5 horizontal feet through the air and pass through a hole into the drop box. Using the slide you selected above, determine how far below the slide (h) to place the hole in the drop box. Yo = 5.2017/5 BLADE 2 RAMPE SLIDE 8⁰ SLIDE Acceptable? (Yes or No) $' Cost 51 In DROP…
The planning department of Abstract Office Supplies has been asked to determine whether the company should introduce a new computer desk next year. The department estimates that $7,000 of new manufacturing equipment will need to be purchased and that the cost of constructing each desk will be $200. The department also estimates that the revenue from each desk will be $550 a. Determine the revenue function R(x) from the sale of x desks. R(x) = Clear all Check answer View an example et more help - Help me solve this 9:05 PM 1/24/2022 L390 Y Insert Home End F12 F10 F11 F9 F7 F8 Esc F5 F6 F4 F3 F2 FnLock F1 & %23 $4 80 9. @ 7 2 3 4 Y