The wide-flange shape has dimensions of b= 7.30 in., t;= 0.5 in., d 18.2 in., and tw-0.3 in. A vertical shear force of V- 51000 lb acts on the cross section. Determine the shear flow magnitude and the shear stress magnitude that acts in the shape: (a) at section 1-1. (b) at section 2-2. (c) at section 3-3 where a = 1.9 in. by a 3 Part 1 Calculate the area moment of inertia for the cross-section about the z-axis. Answer: 1z- i in.4 Save for Later Attempts: 0 of 1 used Submit Answer

The wide-flange shape has dimensions of b= 7.30 in., t;= 0.5 in., d 18.2 in., and tw-0.3 in. A vertical shear force of V- 51000 lb acts on the cross section. Determine the shear flow magnitude and the shear stress magnitude that acts in the shape: (a) at section 1-1. (b) at section 2-2. (c) at section 3-3 where a = 1.9 in. by a 3 Part 1 Calculate the area moment of inertia for the cross-section about the z-axis. Answer: 1z- i in.4 Save for Later Attempts: 0 of 1 used Submit Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1- Determine the location of the shear center for the following section and the shear stress at point A, if a 20 kN (downwards) shear load is applied at the shear center. Given: h1 = 25 mm hi h = 100 mm b = 50 mm Thickness 4 mm 0• ke hi -ь —
a. Determine the location of the shear center for the following section. b. Determine the shear stress at point A, if a 20kN (downwards) shear load is applied at the shear center. Given: h1= 25mm h = 100mm b = 50mm Thickness = 4mm
Determine the location of the shear center for the following section. Determine the shear stress at point A, if a 20 kN (downwards) shear load is applied at the shear center. Given: h1 = 25 mm h = 100 mm b = 50 mm Thickness = 4 mm. V ke- A |▬▬b▬|| h₁
Problem 3: Member AC is subjected to a vertical force of 3 kN. Cross sectional area of tie rod is 400 mm? and the contact area at C is 650 mm?. O Determine the force in the tie rod if the average compressive stress at C is equal to the average tensile stress in the tie rod AB. ® Determine the compressive force at C. Determine the position x of the 3 kN force from A. 3 kN 200 mm
A steel pipe (D = 3.500 in.; d = 3.068 in.) supports a concentrated load of P = 617 lb as shown. The span length of the cantilever beam is L = 4 ft. Determine the magnitude of the maximum bending stress in the pipe. O 21.55 ksi O 13.81 ksi O 15.73 ksi O 24.04 ksi O 17.18 ksi L B P d Pipe cross section. D
1-50. The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps at the top and bottom distribute the load uniformly throughout the block, determine the average normal and average shear stress acting along section a-a. 600 N 30° 50 mm 50 mm 600 N 150 mm 50 mm
4. Compute the maximum shear stress.
The extruded plastic shape will be subjected to an internal shear force of V= 355 lb. Dimensions of the cross section are b-1.7 in.d- 3.4 in, c-2.3 in, and t-0.14 in. Determine: (a) the horizontal shear stress at points A and B. (b) the horizontal shear stress at point C, which is located at a distance of yc-1.2 in. below the z centroidal axis. (c) the maximum horizontal shear stress in the extrusion. yc B (typ.)
! Required information For the beam and loading shown, consider section n-n. Given: P= 155 kN. a 72 mm 450 mm 72 mm 72 mm t=6 mm 600 mm 192 mm Determine the largest shearing stress in that section. MPа. The largest shearing stress is
Question 2: The bars of the truss each have a cross-sectional area of 340 mm2. If the maximum average axial stress in any bar is not to exceed 250 N/mm2, determine the maximum magnitude P of the loads that can be applied. 2m 2P 3m C
Problem 7.3 Consider the T-beam shown in (Figure 1). Take w₁ = 10 kN/m and 2 = 15 kN/m. Figure W1 poten -3 m- W2 B +1.5m 200 mm C 200 mm 20 mm |--20 mm Part A Determine the maximum shear stress in the T-beam at the section where the internal shear is maximum. Express your answer to three significant figures and include the appropriate units. Submit O Tmax=4.84 μ Provide Feedback μА Ω % O MPa ***** X Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining <
2. With an evenly distributed superimposed load of 25 kN/m, a W420 x 85 steel beam is adequately restrained. The beam spans 10 meters. Properties: A- 10839.09 mm? bị - 180.08 mm t, - 11.01 mm d- 420.02 mm 1- 310 x 10° mm* t- 18.08 mm 1. Determine the bending stresses in MPa. 2. Calculate the maximum shear stress in the web in MPa, 3. Determine the magnitude of the greatest horizontal shear stress in MPa.