the water level in a PWR must always be above the top of the active core. a. Estimate the decay heat at the time of scram of a 1,200 MWe reactor. b. Calculate the boiloff rate [kg/hr] if the coolant were saturated at 2200 psi for this decay heat rate. The area of the core occupied by water is 55 ft2 c. Calculate the rate at which the water level would decrease for this boiloff rate [cm/s]. d. What is the importance of keeping the core covered?

the water level in a PWR must always be above the top of the active core. a. Estimate the decay heat at the time of scram of a 1,200 MWe reactor. b. Calculate the boiloff rate [kg/hr] if the coolant were saturated at 2200 psi for this decay heat rate. The area of the core occupied by water is 55 ft2 c. Calculate the rate at which the water level would decrease for this boiloff rate [cm/s]. d. What is the importance of keeping the core covered?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heat pump .11 A building owner wants to apply a heat pump in his building. It has already been decided that the building will have a central heating system. He wants to choose the most energy efficient combination of options. Which combination of the following options will lead to the highest SCOP? (Note: multiple answers possible) Radiators using the range 40-60 [OC] Floor heating using the range 30- 45 [OC] A ground source heat pump An outdoor air heat pump
thermodynamics cycle
Engine Cycle: Our inventor is still trying to design a heat engine that will outperform the Carnot cycle .. Design #801-456 is for an ideal, reversible engine that operates with the cycle shown below (A → B → C → D → A). The engine contains 0.421mol of a gas that has a heat capacity ratio of y = 1.300. Point Pressure [N/m²] Volume [m³] Temperature [K] A 1.05 x 105 0.010 300 B 1.85 x 105 0.010 529 1.85 x 105 0.014 751 D 1.05 x 105 0.014 426 PA B A D V (a) What is the efficiency of this engine cycle? (b) What is the efficiency for a Carnot cycle working between the same maximum and minimum temperatures?
An electric hot water heater consumes 3.1 kilowatts of electricity and converts it to heat. How long will it take the water heater to heat a 67 gallon tank of water from 10 degrees Celsius to 50 degrees Celsius? (1 kilogram of water is 0.37 gallons, 1 Calorie = 4200 J). It may be helpful to refer back to the weekly handout for guidance on this problem. Your final answer should be in minutes (rounded to the nearest 10 minutes).
12. Imagine a solar collector for hot tap water in a hot climate. De outdoor temperature is 22 degree Celsius. De tank of the solar collector is placed outside, and the cold water temperature to the collector is 20 degree Celsius. De water flow rate through the collector is 45 liter/hour. De collector is 2 [m2] and the average solar radiation in the time period considered is 1000 [W/m2]. What is the temperature of the hot water to the tank? The efficiency of the collector can be assumed to be 0.7 (we neglect the dependency to the water temperature) (multiple choice, one answer) 34 [OC] 47 [OC] 54 [OC] 67 [OC] 74 [OC]
276mmx164mm compressor has a piston displacement of 0.039cum/s, what is the operating speed of the compressor if [13] one cyclinder [14] V8 [15] W16 Please answer this immediately. Thank you!
A power plant condenser diverts from the power plant water that condenses heat at a rate of 34 [MW] The cooling water enters the condenser at a temperature of 15c and leaves at a temperature 30C lower than the water's condensation temperature. The pressure of the water at the exit of the turbine is 9[kpa]The condenser is made of brass tubes with an inner diameter of 25mm and an outer diameter of 30mm and the number of tubes in the condenser is 1000 A. Calculate the cooling water flow.B. Calculate the area of the heat exchanger on the condensing side
Completely solve and provide the diagram. Box the final answer. Write legibly 4. A single effect water evaporator operating at 125 kPa abs vapor pressure. Motive steam is available for evaporation at 1.0 MPa with 90% vapor content, what is the mean temperature difference?
[MO31] THERMODYNAMIC CYCLES It is proposed to build a 1000 MWelectric power plant with steam as the working fluid. The condensers are to be cooled with river water. The maximum steam temperature is 550 C, and the pressure in the condensers will be 10 kPa. Estimate the temperature rise of the river downstream from the power plant. A. AT = 4.9 deg C Power B. AT = 3.9 deg C plant C. AT = 2.9 deg C D. AT = 1.9 deg C Discharge Intake 60 m- 8 m deep River mean speed 10m/minute
An ideal gas flows through a horizontal tube at steady state. No heat is added, and no shaft work is done. The cross-sectional area of the tube changes with length and this causes the velocity to change. (a) Derive an equation relating the temperature to the velocity of the gas.(b) If nitrogen at 150 [°C] flows past one section of the tube at the velocity of 2.5 [m/s], what is the temperature at another section where its velocity is 50 [m/s]? Let Cp = 7/2R.
Combustion of a fuel sampie in a bomb calorimeter increases the temperature of the entire system by 5.10 °C if the calorimeter contains 1500 g of water, but only by 4.00 "Cif the calorimeter contains 1950g of water. What is the heat capacity of the dry bomb calorimeter assembly? Assume that the specific heat capacity of water is 4.18 J A. 570 J "C- B. 912 J "C-1 C. 722 J "C- D. 366 J "C-1 E. 494 J "C-
1. What is a fluid? kg [6 marks] 2. A tank is filled with oil with density p = 830; If the volume of the tank is V = 1.01m³ determine the amount of mass in the tank in kilograms. Show your workings. m³ [6 marks] 3. A pipe of diameter 0.18 m has a flow rate of 0.025 m³/s, what is the average velocity in the pipe? Show your workings. [6 marks] 4. The flow rate in a pipe is 1446 litres per minute, what is this in SI units Show your workings. )? [5 marks] 5. The equation below is a simplified form of the continuity equation. dm dt CV Σmin -Σmout The derivative term with respect to time is which of the following: a. The rate of change of the mass within a given control volume b. Always zero by definition c. Zero for transient time dependant flow conditions d. Zero when the mass flow rate coming into the control volume is smaller than the mass flow rate exiting the control volume e. Zero when the mass flow rate entering the control volume is greater than the mass flow rate leaving the…