The voltage Ve(t) (in V) and the current i(t) (in Amp) t seconds after closing the switch in the circuit shown are given by: Vd1) = V,(1 - et/%) i(1) = e, where to = RC is the time constant. Consider the case where Vo = 24 V, R = 3800 Q and C = 4000 x 10-6 F. Determine the voltage and the current during the first 20 s after the switch is closed. Create a vector with values of times from 0 to 20 s with spacing of 2 s, and use it for calculating V(t) and i(t). Display the results in a three-column table where the values of time, voltage and current are displayed in the first, second, and third columns, respectively. (To display values in a Table, just create a matrix and have its output displayed) Script o

The voltage Ve(t) (in V) and the current i(t) (in Amp) t seconds after closing the switch in the circuit shown are given by: Vd1) = V,(1 - et/%) i(1) = e, where to = RC is the time constant. Consider the case where Vo = 24 V, R = 3800 Q and C = 4000 x 10-6 F. Determine the voltage and the current during the first 20 s after the switch is closed. Create a vector with values of times from 0 to 20 s with spacing of 2 s, and use it for calculating V(t) and i(t). Display the results in a three-column table where the values of time, voltage and current are displayed in the first, second, and third columns, respectively. (To display values in a Table, just create a matrix and have its output displayed) Script o

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter3: Assignment, Formatting, And Interactive Input

Section3.6: A Case Study: Acid Rain

Problem 7E

See similar textbooks

Similar questions

The displacement of an oscillating spring can be described by x = A cos(wt) where x = displacement at time t, A = maximum displacement, w = angular frequency, which depends on the spring constant and the mass attached to the spring, and t = time. Find the displacement, x, with maximum displacement A of 4 cm, for times from 0 to 120 seconds with increments of 30 seconds, and angular frequencies from 0.4 to 0.6 radians/sec, with increments of 0.1 radians/sec. The displacement for all combinations of times and angular frequencies needs to be calculated. Use meshgrid. Display your results in a matrix with angular frequencies along the top row and times along the left column like so (you may put zero, 0, or NaN, in the upper left corner:
A simple pendulum is formed of a rope of length L = 2.2 m and a bob of mass m. %3D When the pendulum makes an angle e 10° with the vertical, the speed of the %3D bob is 2 m/s. The angular speed, e', at the lowest position is equal to: (g = 10 m/s^2)
Two small charged objects attract each other with a force F when separated by a distance d.If the charge on each object is reduced to one-fourth of its original value and the distance between them is reduced to d/2,the force becomes?
The mole balance equation for the phase separator is ziF=yiV + xiL.What does the F represent in this equation? Group of answer choices molar flow rate of the liquid molar flow rate of the vapor molar equilibrium total molar flow rate
A discharge factor is a ratio which compares the mass flow rate at the end of a channel or nozzle to an ideal channel or nozzle. The discharge factor for flow through an open channel of parabolic cross-section is: K = 1.2 [V16x +1+ In(V16x² +1+4x)]³ 4x where x is the ratio of the maximum water depth to breadth of the channel at the top of the water. Determine the discharge factors for x in the range 0.45 to 0.90 in steps of 0.05. Script e C Reset I MATLAB Docume 1 %Give values for x: 2 3 %Solve for K: 4
The van der Waal's equation of state is given as RT a v-b v² For sulfur dioxide at temperature, T, of 300 K and a pressure, P, of 1 atm, the constants are given as: R = 0.08206 L.atm/(mol.K) L2.mol² P = a = 6.7689 atm.L b=0.05679 L.mol™¹ a) Plot the function f(v)=0 the for volumes for the range of 0 to 40 L/mol using 0.5 increment. b) Identify the root in this plot (where the curve crosses x-axis). c) Use the MATLAB function (fzero) to solve the original f(v) function for the specific volume using the initial guess from part (c). d) Use the MATLAB function (roots) to solve the original f(v) function for the specific volume.
When a tension force of 900 N is applied to a steel wire, it is assumed that E = 210 GPa and that the diameter of the wire increases by 1.05 mm. Calculate the diameter of the wire.
An oscillating current in an electric circuit is described by i(t) = 9e cos(2rt) where t is in seconds. Use False Position Method to determine the value of t such that i=3.5. Plot the graph of the function to develop your initial guess. Terminate your computation when the approximate relative error falls below ɛs=10°. Give the results in a table.
Q2: In a dielectric material (ɛ = 5ɛ, ), the potential field V= 10xyz - 5z? V, determine (a) E, (b) D, (c) P, (d) P.
(Conversion) An object’s polar moment of inertia, J, represents its resistance to twisting. For a cylinder, this moment of inertia is given by this formula: J=mr2/2+m( l 2 +3r 2 )/12misthecylindersmass( kg).listhecylinderslength(m).risthecylindersradius(m). Using this formula, determine the units for the cylinder’s polar moment of inertia.
2. calculates the trajectory r(t) and stores the coordinates for time steps At as a nested list trajectory that contains [[xe, ye, ze], [x1, y1, z1], [x2, y2, z2], ...]. Start from time t = 0 and use a time step At = 0.01; the last data point in the trajectory should be the time when the oscillator "hits the ground", i.e., when z(t) ≤ 0; 3. stores the time for hitting the ground (i.e., the first time t when z(t) ≤ 0) in the variable t_contact and the corresponding positions in the variables x_contact, y_contact, and z_contact. Print t_contact = 1.430 X_contact = 0.755 y contact = -0.380 z_contact = (Output floating point numbers with 3 decimals using format (), e.g., "t_contact = {:.3f}" .format(t_contact).) The partial example output above is for ze = 10. 4. calculates the average x- and y-coordinates 1 y = Yi N where the x, y, are the x(t), y(t) in the trajectory and N is the number of data points that you calculated. Store the result as a list in the variable center = [x_avg, y_avg]…
Find the impedance theoretically of a wire if it carries the frequency 10 kHz have a voltage is 8v, the current is 2mA, resistance is 13 k, inductance 29 mH and capacitance 0.1 uf