The voltage and current at the terminals of the circuit element in (Figure 1) are zero for t <0. For t≥ 0 they are v=430e 100 sin 200t V, i7e-100 sin 200t A. Figure + v -1 - 20 1 of 1 Find the total energy absorbed by the element. Express your answer to three significant figures and include the appropriate units. W = μÃ Value I J ?

The voltage and current at the terminals of the circuit element in (Figure 1) are zero for t <0. For t≥ 0 they are v=430e 100 sin 200t V, i7e-100 sin 200t A. Figure + v -1 - 20 1 of 1 Find the total energy absorbed by the element. Express your answer to three significant figures and include the appropriate units. W = μÃ Value I J ?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

ansivered MEked out c Ammeter Find the impedance theoretically of a wire if it canies the frequency 10 kHz have a voltage is 8v, the current is 2mA, resistance is 11 k2, inductance 26 mH and capacitance 0.2 uf NOTE Write your Answer in the box without the unit. Question Not yet answered Marked out of Z= 3.00 P Flag question restion 6 Write all the steps and experimental setup to measure the numerical aperture of a plastic graded-index opt fiber in your own words? Fyet P Type here to search hp
The sinusoidal voltage source in the circuit seen in (Figure 1) is operating at a frequency of 54 krad/skrad/s. The coefficient of coupling is adjusted until the peak amplitude of i1 is maximum. What is the peak amplitude of i1 if vg=429cos(5.4×104t)V?
7. In a pure inductive circuit, the phase angle between the voltage waveform and current waveform will havephase shift * 180 deg O deg 45 deg O 90 deg 8. Why do we say the "voltage across" or "the voltage with respect to?" Why can't we just say voltage? * Voltage is a measure of electric potential difference between two electrical points. O It's an electrical cliche. The other point could be negative or positive. None of the above.
SMTH 00 References Mailings Review View Help AaBbCcD AaBbCcDe AaE D- A - I Normal T No Spac. Head Paragraph 2. Find the equivalent inductance of the circuit if L= 20H 25 H 20 H 20 H 60 H 10 H 30H acer
Find the total inductance at the terminals a-b, for the circuit shown in FigureQ2(b). 25 µH 18 μΗ " a 60 μΗ 20 µH 30 μΗ 75 μΗ 12 μΗ 15 μΗ 38 μΗ Figure Q2 (b)
Activity 1: You are testing an electrical device which can be modelled by the figure shown below: 18 -j12 a b j6 -j10 it E1 12 13 E2 13 The above electric circuit can be characterized by the following equations: 1811 + j6(11 – 12) + 4(11 – 12) = 1020° -j1212 + 8(12 – I3) + 20490° + 4(I2 – 4) + j6(I2 – I1) = 0 -j1013 + 1313 – 20290° + 8(13 – 12) = 0 Find I1, I2, and I3 using the Gaussian elimination method.
A 1-H inductor is connected in series with a 6-ohm resistor. If the connection is energized from a 9-V DC source, determine the current (in amperes) through the circuit for a long time. The initial current is 100 mA. Express your answers accurate to four decimal places. No need to put the units.
Calculate the total inductance at the terminals a-b, for the circuit shown in FigureQ2(b). 10mH 5mH 15mH ll ell ell 20mH 40 mH 60 mH 80mH bo Figure Q2 (b) ll
If an electrical circuit draws 100W + J100VAR from a sinusoidal source, then what would the circuit be? Explain why. a) a pure resistor circuit b) a series or parallel R-L circuit c) a series or parallel R-C circuit d) a series L-C circuit
A current of i = 5 + 10 sin 377t + 377t Ampere flows through a series circuit containing resistance of 5 ohms and an inductance of 13.26mH. Determine the expression of the total voltage. a. e=25+70.7 sin (377t + 45°) Volts O b. e 25+ 70.7 sin (377t - 45°) Volts = O c. e = 25 + 70.7 sin (377t – 30°) Volts O d. e 25+ 70.7 sin (377t +30°) Volts
Q1. Estimate the unknown value of inductance (L1) for the circuit shown in Figure A. A L1 = L4 1.5mH L5 4mH LT= 9mH L2 8mH L3 L6 B 2.5mH 2.5mH
5) Find the reactance the inductance and impedance of the circuit. Calculate the current of this circuit and the sketch waveform of current and voltage. V1 10 V 60 Hz R1 m 100kQ 12 Vrms 1000 Hz 0° 6) Find the reactance the inductance and impedance of the circuit. Calculate the currents of this circuit R www 502 L L1 106mH eee 10 mH