The voltage 8 sin (400t) is applied to a series RLC circuit, with R = 200 Q, L = 0.1 H, and C = 1 µF (1µ=106). (a) What is the impedance Z? (b) What is phase angle 0? (c) What is the behaviour of the circuit, inductive, resistive, or capacitive? (d) At what frequency will the circuit be purely resistive (no effect from the capacitor and the inductor)? Show your detailed work.

The voltage 8 sin (400t) is applied to a series RLC circuit, with R = 200 Q, L = 0.1 H, and C = 1 µF (1µ=106). (a) What is the impedance Z? (b) What is phase angle 0? (c) What is the behaviour of the circuit, inductive, resistive, or capacitive? (d) At what frequency will the circuit be purely resistive (no effect from the capacitor and the inductor)? Show your detailed work.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 1PP: Capacitive Circuits Fill in all the missing values. Refer to the formulas that follow....

See similar textbooks

Similar questions

List the five capacitor replacement rules.
Capacitive Circuits Fill in all the missing values. Refer to the formulas that follow. XC=12fCC=12fXCf=12CXc Capacitance XC Frequency 38 F 60 Hz 78.8 400 Hz 250 pF 4.5 k 234 F 10 kHZ 240 50 Hz 10 F 36.8 560 nF 2 MHz 15 k 60 Hz 75 nF 560 470 pF 200 kHz 6.8 k 400 Hz 34 F 450
Multicolour LED Mono LED Dimensional LED The capacitor in a clamper circuit is in parallel with the voltage source * None True False For the following circuit, the vo waveform is wwwww
The attached image shows a circuit with an AC voltage source, a resistor, inductor, and capacitor connected in series. The circuit has the following characteristics: Resistor resistance: 10 ohm Capacitor capacitance: 0.05 F Inductor inductance: 13 H Current Amplitude: 4 A Voltage amplitude across the source: 60 V Frequency at the source: 0.3 Hz Voltage amplitude across the resistor: 35 V Voltage amplitude across the capacitor: 37 V Voltage amplitude across the inductor: 80 V (a) Calculate the RMS voltages from the amplitudes above. From the RMS voltages across the capacitor, inductor and resistor, calculate the RMS voltage of the AC source. Hint: Vrms = V0/sqrt(2) Vrms = sqrt( (Vrms,R)2 + (Vrms, L - Vrms, C)2 ) (b) Calculate the RMS value of the current (c) Using the resistance, capacitance, inductance, and the frequency of the AC voltage, calculate the impedance Z. From this, and the previously measured value of Vrms, find the RMS value of the current in the circuit.
Describe the resulting waveforms when the capacitors (initially 20uF and then replaced with 100uF) were connected in parallel with the load
In a purely inductive circuit, the inductor voltage and inductor current are 90 degrees out of phase. Which of the following apply to a purely inductive circuit? voltage lags current by 90 degrees O current leads voltage by 90 degrees voltage leads current by 90 degrees O current lags voltage by 90 degrees
An RLC series circuit has a power factor of 84%. The resistor has a voltage drop of 96 volts. What is the total voltage applied to the circuit? 10giaton0o of 18. 0 The inductor has an induc-
3) Pure Inductance in Series Frequency = 60HZ EL1 = E2 = E13 = %3D ET = 2kV
Find the phase and amplitude of the voltage on the inductance. C = 100uF L = 0.15H R =120 VR V. Vc I Vs 100V, 50HZ
In a series LR circuit, the reactance of the inductance is 520 ohm. What will be the value of the inductor if the frequency of the AC is 60 HZ?
100mH has initial equivalent resistance is 15 ohms. What is the parallel capacitance that will cause resonance frequency at 60 Hz at 220 ac source
Problem [13] Determine the equivalent inductance at terminals a and b. 10 mH 60 mH 25 mH 20 mH a o ll 30 mH rell