The uniform rod having a weight W and length / is supported at its ends A and B by two identical supports as shown in Figure below. As the end B is lifted it is observed that the rod is on the verge of slipping when e = 30°. Determine the coefficient of static friction Hs at A and B. Neglect the thickness of the rod for the calculation. B e =30°

The uniform rod having a weight W and length / is supported at its ends A and B by two identical supports as shown in Figure below. As the end B is lifted it is observed that the rod is on the verge of slipping when e = 30°. Determine the coefficient of static friction Hs at A and B. Neglect the thickness of the rod for the calculation. B e =30°

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.49P

See similar textbooks

Similar questions

The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.25, determine the largest angle 6 for which the assembly will remain at rest.
The screw of the clamp has a square thread of pitch 0.16 in. and a mean diameter of 0.6 in. The coefficient of static friction between the threads is 0.4. Determine (a) the torque C0 that must be applied to the screw in order to produce a 28-lb clamping force at A; and (b) the torque required to loosen the clamp.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The winch in the figure is used to move the 135 kg uniform log. The coefficient of static friction between the log and the plane is 0.40. @ Compute the tension T for impending sliding. 2 Compute the tension T for impending tipping. 3 Compute the max. tension that can be applied for which the log remains at rest @ Compute the normal reaction between log and plane. 5 Compute the location of the normal reaction from A. T- log 60 B -2.4 m
The clamp exerts a 145 lb compressive force on the wood blocks. Single-threaded screw BC has lead L = 0.190 in. and mean diameter d = 0.370 in. It turns in the threaded sleeve at C and pushes against B. The coefficient of static friction between the screw threads and the threaded sleeve is = 0.300. Neglect friction at B. 2 in. 2 in. 2 in. B 2.25 in. 2.40 in. 2.25 in. (a) Determine the value of the moment M in ft · Ib to increase the clamping force. (Enter the magnitude.) ft · Ib (b) Determine the value of the moment M in ft · Ib to decrease the clamping force. (Enter the magnitude.) ft · Ib
The green rods apply a 2.6 kN clamping force to the red object, E. The square-threaded screw used to generate the clamping force passes through a threaded opening at B and presses against lever ACE at E. The coefficient of static friction is = 0.29. Neglect friction at A. The screw has mean radius r = 9 mm and lead L = 2 mm. B 180 mm 70 mm E (a) Determine the force in member CD in kilonewtons. (Enter the magnitude.) kN (b) Determine the magnitude of the moment in N• m that one must apply to the screw to increase the clamping force. N: m (c) Determine the magnitude of the moment in N •m that one must apply to the screw to decrease the clamping force. N: m
A homogeneous block of weight W rests upon the incline shown in the figure. If the coefficient of friction is 0.30, determine the greatest height h at which a force P parallel to the incline may be applied so that the block will slide up the incline without tipping over.
3- Can the system in figure be in static equilibrium in the position shown? The uniform bar AB weight 500 lb, and the weight of block C is 300 lb .Friction at A is negligible and the coefficient of static friction is 0.4 at the other two contact. 10 ft В 30° C 50°
The uniform concrete block has a weight of 300 lb. The coefficients of static friction are μA = 0.2, μB = 0.3, and between the concrete block and the floor, μ = 0.4. (Figure 1) Determine the smallest couple moment that can be applied to the 190-lb wheel that will cause impending motion.
The high strength, square-threaded bolt that holds the three plates together has a nominal diameter of 1 in. The coefficient of friction is us = 0.36. The mean diameter of the thread is 0.94 in. The lead of the bolt is L = 0.160 in. Neglect friction between the nut and the washer. Determine the torque one must apply in in. Ib to the nut to induce a tension of 47,500 lb. (Enter the magnitude.) in. · Ib When that tension is achieved, determine the torque in in. · Ib required to loosen the bolt. (Enter the magnitude.) in. • Ib
The uniform cylindrical drum weighs 250 lbs and is supported by a frictionless roller at A and the frame at C. The coefficients of friction between the frame and the drum at C are as follows, static coefficient u: = 0.3 and kinetic coefficient uk = 0.25. If the drum is at rest, find M required to start the drum moving? For full credit show a labeled free-body diagram. 2' 30°