The undersea research vehicle Alvin has a spherical pressure hull 1 m radius and shell thickness of 30 mm. The pressure hull is steel having a yield point of 700 MPa. Determine the depth of submergence that would set up the yield-point stress in the spherical shell. Consider sea water to have specific weight of 10.27 kNper cubic meter

Q: Determine the normal stress in a ball, which has an outside diameter of 180 mm and a wall thickness…

A: Given data in question  Pressure  Outside diameter  Thickness To find out  Normal stress

Q: Q3. For the beam shown in Fig. 3.compute: 1. The maximum shearing stress developed in the beam. 2.…

A: We have to determine the value of maximum shearing stress developed in the beam and shearing stress…

Q: After filling the tank shown in Figure 3a, the plane of the major principle stress in element A will…

A: A cylindrical tank of dia 10m, and surcharge stress of 100 KP a.Unit wt of soil = 16 KN/m3Depth of…

Q: A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm. If the…

A:

Q: A solid shaft of 100 mm diameter in a small hydraulic turbine is subjected to an axial compressive…

A: given- dia =100 mmaxial compressive load=100π kNtorque=5π kN-m

Q: A thin walled cylindrical pressure vessel having a radius of 0.5m and wall thickness of 25mm is…

A:

Q: a cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm, can only be…

A: It is required to determine the radius of spherical vessel. V=43πr30.075 m3=43πr3r3=0.018 m3r=0.26 m…

Q: The constant wall thickness of a tube with the elliptical cross section shown is 0.15 in. What…

A: ASKED: To determine the torque that will cause the given shear stress in the shown elliptical…

Q: The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 91 mm, and t = 4 mm. (a)…

A:

Q: A thin walled cylindrical pressure vessel having a radius of 0.5 m and wall thickness of 25 mm is…

A:

Q: When filled to capacity, the unpressurized storage tank shown in Figure contains water to a height…

A: Using formula to find hoop stress

Q: A concentrated vertical load of 3000 KN is applied on a horizontal ground surface. Points P and Q…

A: Given data -  Concentrate vertical load = 3000 KN Depth of point (P) = 1 m  Depth of point (Q) = 2 m…

Q: 5 m +A 5 m 5 m 10 m

A: Given: A rectangular loaded area as shown below Required to determine a) Stress at a depth of 5 m…

Q: Problem 3. Segment AB of the bar is a tube with an outer diameter of 2.5 in. Segment BC is a solid…

A: Given- Two bar segment subjected to load of 2800lb and 4500lb at C and B respectively. Required- To…

Q: 1. The active lateral stress ratio is a. always larger than always smaller than b. c. always equal…

A:

Q: The extruded plastic shape has dimensions of D = 26 mm, d = 20 mm, a = 85 mm, and t = 8 mm. (a)…

A: The dimensions of the extruded plastic shape are:-D = 26 mm d = 20 mma = 85 mm t = 8 mmTo…

Q: Calculate the stress distribution with depth below the center of the dam, and the stres distribution…

A:

Q: A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is…

A: Given : Radius of the shell is increased by = 1% Thickness is reduced by 1 % To Determine : The…

Q: A spherical ball of volume 106mm³ is subjected to a hydrostatic pressure of 90 kN/m². If the bulk…

A: Given- Volume of spherical ball V=106 mm3 Hydrostatic pressure P=90 kN/m2 Bulk modulus K=180 MPa It…

Q: 4. In a plane wave front, the pressures in the plane of the wave front are v/(1-v) times the…

A:

Q: A hemispherical head with r= 15.0 in. is subjected to an internal pressure of 4000 psi. If the…

A: This question is related to the Strength of Material  In this question we calculate thickness of…

Q: Q1: Find the boundary layer thickness (6) equation, the shear stress (t) and the coefficient of drag…

A: Given velocity profile: uU=2yδ-3yδ2+3yδ5 Using von Karman momentum integral equation τoρU2=dθdc:…

Q: A hemispherical pressure vessel with a diameter of 2 m and a wall thickness of 30 mm is filled with…

A:

Q: The vertical surface stress is 100 kPa. The stress increase (kPa) at A is 2m 100 kPa 2m 2m A 1m 19.3…

A:

Q: 45° 2 m The cylindrical tank with a spherical endcap has an outer radius of 2 m and a wall thickness…

A:

Q: redfus af the tube (8) = 2 mm = 2X10m Surface tenston ()= 0.752N/m %3D wetting angle 10) = 130 To…

A: As per the capillary action in a tube we have to determine the value of capillary rise in the tube…

Q: Question A thin walled cylindrical pressure vessel having a radius of 0.5 m and wall thickness of 25…

A: Given- Thin walled cylindrical pressure vessel- Radius r = 0.5 m Wall thickness t = 25 mm Internal…

Q: The vertical surface stress is 100 kPa. The stress increase (kPa) at A is 100 kPa 2m 2m 2m 4.4 O 20…

A:

Pressure and Stress