The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A₁ = 350 mm² and a length of L₁ = 2.1 m. Rod (2) has an area of A₂ = 375 mm² and a length of L₂ = 1.5 m. Assume dimensions of a = 3.2 m, b = 1.1 m, and c = 1.4 m. After a load of P = 130 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) a L2 Rigid bar L₁ Answer: (a) σ₁ = i 02= i (b) VD= i (1) B MPa MPa mm -X,U b C ↓ С D P

The two vertical steel [E = 200 GPa] rods that support rigid bar ABCD are initially free of stress. Rod (1) has an area of A₁ = 350 mm² and a length of L₁ = 2.1 m. Rod (2) has an area of A₂ = 375 mm² and a length of L₂ = 1.5 m. Assume dimensions of a = 3.2 m, b = 1.1 m, and c = 1.4 m. After a load of P = 130 kN is applied to the rigid bar at D, determine: (a) the normal stresses in rods (1) and (2) (b) the magnitude of the downward deflection of the rigid bar at D. y,v (2) a L2 Rigid bar L₁ Answer: (a) σ₁ = i 02= i (b) VD= i (1) B MPa MPa mm -X,U b C ↓ С D P

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.45 in.2. After load P is applied, the strain in bar (1) is found to be 850 μεμε. Assume L1=53 in., L2=79 in., a=34 in., b=33 in., and c=30 in. Determine:(a) the stresses in bars (1) and (2).(b) the vertical deflection vD of point D on the rigid bar.(c) the load P.
Q2: The pin-connected structure shown in figure below consists of a rigid member BED and three steel rods (E= 200 GPa). Each of the rods AB and CD has a 200 mm? cross-sectional area and rod EF has a 625 mm? cross-sectional area. If a load of P= 36 kN is applied at E, determine: (a) the change in length of rod EF. (b) the stress in each rod. B. 300 mm E P=36 kN 300 mm 400 mm 500 mm
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. L. C D VAR 2m +12m -1.2 m-1.2 m 1.2 m-
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.² and bar (2) has a cross-sectional area of 0.425 in.². After load P is applied, the strain in bar (1) is found to be 780 μe. Assume L₁-60 in., L₂=90 in., a=40 in., b=40 in., and c=30 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. Answers: (a) σ₁ = (b) VD = i (c) P = Mi i L₁ a (1) B L2 b in. C ksi, 0₂ = i kips. с tel D P ksi.
A steel [E = 200 GPa] bar (1) supports beam AB. The cross-sectional area of the bar is 540 mm?. If the stress in the bar must not exceed 450 MPa and the maximum deformation in the bar must not exceed 20 mm, determine the maximum load P that may be supported by this structure. Use dimensions of a = 4 m, b = 2.4 m, and c = 5.2 m. (1) B' A a Answer: P = i kN
Q2: The pin-connected structure shown in figure below consists of a rigid member BED and three steel rods (E= 200 GPa). Each of the rods AB and CD has a 200 mm? cross-sectional area and rod EF has a 625 mm? cross-sectional area. If a load of P= 36 kN is applied at E, determine: (a) the change in length of rod EF. (b) the stress in each rod. A 300 mm E P-36 kN 300 mm DIO 400 mm 500 mm
Rigid bar ABCD is loaded and supported as shown. Steel [E = 28400 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.82 in.² and bar (2) has a cross-sectional area of 0.41 in.². After load P is applied, the strain in bar (1) is found to be 700 μe. Assume L₁=69 in., L₂-89 in., a=34 in., b=33 in., and c-37 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection VD of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD = (c) P= i i i L₁ a (1) B L2 b ksi, 0₂ = in. kips. (2) C i D P ksi.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 30000 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.75 in.2 and bar (2) has a cross-sectional area of 0.425 in.2. After load P is applied, the strain in bar (1) is found to be 780 μs. Assume L₁-60 in., L₂=90 in., a=40 in., b=40 in., and c-30 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. A Answers: (a) 0₁ = (b) VD= (c) P = i i i L₁ a L2 in. (2) ksi, 0₂ = i kips. C D P ksi.
3. The rigid bar AC is pinned at A and attached to bars DB and CE as shown in the figure. The weight of AC is 50 kN and the weights of the other two bars are negligible. Consider the temperature of both bars DB and CE to be raised 35°C. Find the resulting normal stresses in these two bars. DB is copper for which E = 90 GPa, ? = 18 × 10–6 /°C, and the crosssectional area is 1000 mm2 , while CE is steel for which E = 200 GPa, ? = 12 × 10–6 /°C, and the cross section is 500 mm2 . Neglect any possibility of lateral buckling of the bars.
Rigid bar ABCD is loaded and supported as shown. Steel [E = 29900 ksi] bars (1) and (2) are unstressed before the load P is applied. Bar (1) has a cross-sectional area of 0.73 in.² and bar (2) has a cross-sectional area of 0.47 in.². After load P is applied, the strain in bar (1) is found to be 800 με. Assume L₁-52 in., L₂=90 in., a-36 in., b-34 in., and c-23 in. Determine: (a) the stresses in bars (1) and (2). (b) the vertical deflection vp of point D on the rigid bar. (c) the load P. (2) (1) L₁ B C a Answers: (a) σ₁ = (b) VD = (c) P = i i L2 b C ksi, 0₂ = i in. kips. D P ksi.
A mild steel bar, 1.5 m long, has a square section 40 mm x 40 mm. The bar is subjected to a two- dimensional stress, , = 310 N/mm² (tensile) and , -300 N/mm² (compressive). E = 2 × 10 N/mm², Poisson's ratio=0.3. The elongation of the bar is the direction of , will be