The two springs have a stiffness k = 1.2 kN/m, and have the same length and are without deform when 8 = 0°. If the mechanism starts from rest when 0 = 01. The mass of each sphere is m. Treat the spheres as particles and neglect the masses of the rods. and springs. Determine when 0 = 02: a) The angular velocity of the mechanism b) If the rod OB supports a normal force of N = 15 N, check if the rod fails (Explain why the rod fails or does not fail) Variables: m, 0₁,0₂ A m 0₁ 0₂ e [kg] [] [°] 2,5 25 7 C 0,25 m

The two springs have a stiffness k = 1.2 kN/m, and have the same length and are without deform when 8 = 0°. If the mechanism starts from rest when 0 = 01. The mass of each sphere is m. Treat the spheres as particles and neglect the masses of the rods. and springs. Determine when 0 = 02: a) The angular velocity of the mechanism b) If the rod OB supports a normal force of N = 15 N, check if the rod fails (Explain why the rod fails or does not fail) Variables: m, 0₁,0₂ A m 0₁ 0₂ e [kg] [] [°] 2,5 25 7 C 0,25 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

20 R3 Which tools that can be used to :3 draw the following shape in .AutoCAD 37 23 43 R3 dimension, circle, arc, line, scale and rectangle 30 dimension, arc, line, rectangle, purge, and block construction line, polygon, arc, polyline, and dimension rectangle, trim, dimension, polyline, circle, and arc O O
Question 3) The length L is given as L=34 m on the plate in the figure. According to this;Question 3-A) Find the X coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)Question 3-B) Find the Y coordinate of the geometric center of the plate. (Enter your result without writing m units. Write at least three digits after the comma.)
Draw the 1st and 3rd Angle Orthographic sketch of the following part:
If Gear C and gear A are having the same pitch diameter gear and gear B is twice (larger) the diameter of gear C. If gear C is turning at the speed of 50 RPM, what would be the Rotational speed of Gear B in RPM. (RPM = revolution per minute)
b)Solve for the Velocity of Point D (m/s) c)Solve for the Velocity of Point C (m/s) d)Solve for the Angular Velocity of Link CE
Identify the operations from the figure re O Turning O Facing O Chamfering O drilling
MULTIPLE CHOICE -The answer is one of the options below please solve carefully and circle the correct option Please write clear .
Draw the orthographic projection of given object with proper dimensioning .
3. Convert the decimal number 35710 into its hexadecimal number equivalent.
Example (Write the position equations (02 input)
! Draw a sketch of the above drawing in A3 (or two A4 paper taped together).
Draw front and right-side views of the following object with a completed dimensions. Draw in scale 1:1 on A4 sheet. (Problem is taken from "Graphics for Engineers' by Earle) 78 What can we learm from the drawlng ? 1. The dimension note M10x1.5 means that the hole is a threaded hole. R16 O 16, 2 Holes The letter 'M' means that the threads are made by following a metric thread system. The number "10" Is the major dlameter of the hole and the number 1.5 is the pitch of a thread. However, for coarse threads, it is a common practice to omit specifying the pitches. For example, a note M10 means the pitches of the thread is 1.5 mm. In this book, the pitch is specified in order to facilitate drafting. 2. Drawing symbol of a threaded hole is shown below. - Thin Ine (4H pench The ends of this arc does not meet together but approximately 90 degs, apart. Object Ihe (2i pencil .major dlameter pich2 M10x1 5 3. The circular projection surface at a threaded hole that is raised from a cylinder is…