The two blocks used in a measuring device have negligible weight. The spring iscompressed 4 in. when in the position shown. The end of the screw is smooth and thecoefficient of static friction at all other points of contact is μ = 0.35. (Figure 1)FigurePk = 20 lb/in.B45°A 60°1 of 1Part ADetermine the smallest axial force P which the adjustment screw must exert on B in order to start the movement of B downward.Express your answer to three significant figures and include the appropriate units.P =SubmitμAValueProvide FeedbackRequest AnswerUnits

Given, Compression of spring, x = 4in Spring constant, k = 20lb/in coefficient of static friction,…

The two blocks used in a measuring device have negligible weight. The spring is compressed 4 in. when in the position shown. The end of the screw is smooth and the coefficient of static friction at all other points of contact is μ = 0.35. (Figure 1) gure k = 20 lb/in. B 45° A 60° < 1 of 1 > Determine the smallest axial force P which the adjustment screw must exert on B in order to start the movement of B downward. Express your answer to three significant figures and include the appropriate units. P= Submit μA Value Provide Feedback Request Answer Units ?

The two blocks used in a measuring device have negligible weight. The spring is compressed 4 in. when in the position shown. The end of the screw is smooth and the coefficient of static friction at all other points of contact is μ = 0.35. (Figure 1) gure k = 20 lb/in. B 45° A 60° < 1 of 1 > Determine the smallest axial force P which the adjustment screw must exert on B in order to start the movement of B downward. Express your answer to three significant figures and include the appropriate units. P= Submit μA Value Provide Feedback Request Answer Units ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 679-N force is applied to the 114-kg block, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the block. The force is positive if to the right, negative if to the left. H₂ = 0.77 = 0.60 Answer: F= i 26° N P = 679 N
Two solid steel shafts (G= 77 GPa) are connected by the gears shown. The support D is fixed, and the bearings allow free rotation of the shaft. The radius of gear B is ³ = 20 mm, and the radius of gear C is rc = 60 mm, If T₁ = 75 Nm, 1. Draw the torque distribution along shaft DE. 2. Calculate the angle through which end A rotates E rc = 60 mm 20 mm 500 mm 24 mm 400 mm
For the beam and loading shown, use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the beam at. A. Assume a constant value of EI = 113000 kip-ft² for the beam; wo = 2.0 kips/ft, LAB = 15 ft. LBC= 8 ft. - Wo A Answer: (a) 8B = (b) VA= LAB rad in. B LBC C X
e) the value of the constant of integration C2. Enter your answer in kNm3 to 3 decimal places.
In the gear system shown in the figure, the motor applies a torque of 231 N-m to the gear at A. A torque of TC = 440 N-m is removed from the shaft at gear C, and the remaining torque is removed at gear D. Segments (1) and (2) are solid 38-mm-diameter steel (G = 80 GPa) shafts, and the bearings shown allow free rotation of the shaft. Assume DA = 110 mm, DB = 370 mm, L1 = 1.7 m, and L2 = 1.1 m. Calculate the rotation angle of gear D relative to gear B.
3. The small sphere shown below has held by two wires with tension To. sphere is released from equilibrium. Determine the ratio To/T1, where T1 is the tension in the remaining wire immediately after the other mass of 2kg. It is initially One wire is cut and the small a one is cut. 30 30
please help with solving. student no is 128425
Determine the value of the uniformly distributed loadd "w". What is the numeric value of C1 ( 1st constant)? Dtermine the deflection at midspan.
10
L=195 cm q-14 N please can you write answers clearly 2q 2- For the beam given in the figure, a Find the equation of elastic curve by integration method. q=a+b+c b- Draw (Tv), (M.) diagrams of the beam. c- Find the support reactions. Explanation: A B
A linear torsional spring deforms such that an applied couple moment M is related to the spring’s rotation u in radians by the equation M = (20 θ) N ⋅ m. If such a spring is attached to the end of a pin-connected uniform 10-kg rod,determine the angle θ for equilibrium. The spring is undeformed when θ = 0°.