The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0.0). After load P is applied.joint B moves to the coordinate position (0.35 in., -0.55 in.). Assumeo - 11 ft, b-7 ft, and h-8 ft. Determine the normal strain in eachbar.Answers:CABEBC3676.02i 5685.14μεμε

Answered: Image /qna-images/answer/f5d2f105-b5a0-4c7e-bdb0-25e44cde3a37.jpg

The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0.0). After load P is applie joint B moves to the coordinate position (0.35 in. -0.55 in.). Assume a-11 ft, b-7ft, and h-8 ft. Determine the normal strain in bar. Answers: CAB- i 3676.02 i 5685.14 pe HE M

The two bars shown in the figure are used to support a load P. When unloaded, joint B has coordinates (0.0). After load P is applie joint B moves to the coordinate position (0.35 in. -0.55 in.). Assume a-11 ft, b-7ft, and h-8 ft. Determine the normal strain in bar. Answers: CAB- i 3676.02 i 5685.14 pe HE M

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

d = 600 6Ø28 75 75 300 can you please show how to find the elastic stress and design ratio? fc' = 27 MPa; M1 = 60 KN-m; M2 = 200 KN-m
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.47 in., -0.12 in.). Assume a = 18 ft, b = 36 ft, c = 12 ft, and d = 24 ft. Determine the normal strain in each bar. с TEIGOLF GOL Answer: EAB EBC i P a (1) 1.252 i 0.882 eTextbook and Media B με με b (2)
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The two bars are used to support load P. When unloaded, joint B has coordinates (0,0). After load P is applied, joint B moves to the coordinate position (-0.40 in, -0.15 in.). Assume a - 18 ft, b-36 ft.c-12 ft, and d-24 ft. Determine the normal strain in each bar. Answer: CAB i fac-i a B με με
A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the left by u = 1.5 mm and upward by v = 4.3 mm to new position Q'. Determine the shear strain y at corner Q' after deformation. Usec = 710 mm, a = 32%, and ß = 58% V Answer: i urad
Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain Ex = 0.005, DA has a normal strain ey = 0.004 at D, Yxy = 0.01rad determine the shear strain at point E with respect to the x' and y' axes. 600 mm- 600 mm E D
Question 2. The square plate ABCD is deformed into the shape shown by the dashed lines. If DC has a normal strain 6x = 0.005, DA has a normal strain e, = 0.004 at D, y = 0.01rad determine the shear strain at point E with respect to the x and y' axes. 600 mm 600 mm
2. Determine the normal stress in members BD, AC, and BC in the truss shown. The cross- sectional area of each member is 1500 mm2. Indicate whether the stresses are tensile (T) or compressive (C). Use 2 decimal places in every solved value. 10 m 10 m 10 m K 6 т H 6 т 15° 15° 50 kN 40 kN E F 6 т C D б т A B
determine the tensile stress in each segment of the bar shown. Segment AB cross section 2in x 2in. Segment BC has a circular cross-section with a diameter of 1.75 in . The tensile load P= 75 kips
An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial stress of bar B; in MPa. 35KN B1 B2 ВЗ ... 10KN 15KN 30KN A 218.75 B 125 C 62.5 D 31.25
The state of strain at point A on the bracket is measured using the strain rosette shown inFigure. Due to the loadings, the readings from the gauges give εa=3x10^-4, εb= -5x10^-4, εc= 4x10^-4. Take the modulus of elasticity as E= 200 GPa and Poisson ratio as ν = 0.3. a.)Determine principal elongation rates and Draw the Mohr’s circle. b.) Determine the principal stresses
A beam having the cross section shown is subjected to a couple M0 acting in a vertical plane. Determine the largest permissible value of the moment M0 of the couple if the maximum stress is not to exceed 103 MPa. Given: Iy = Iz = b4/36 Iyz = b4/72