The trapezoidal channel below must supply a discharge rate of 2 x SN (m/s). The Manning'sroughness of the channel is SN/1000 (s/m/3) and the channel slope is SN/10000.Div2HB = 6.5 mUse MS Excel spreadsheet to set up the problem, and solve for the normal depth D to anaccuracy of 4 decimal places. Show at least 5 iterations in your table.

Consider the free body diagram;

The trapezoidal channel below must supply a discharge rate of 2 x SN (m³/s). The Manning's roughness of the channel is SN/1000 (s/m) and the channel slope is SN/10000. D 2H B = 6.5 m Use MS Excel spreadsheet to set up the problem, and solve for the normal depth D to an accuracy of 4 decimal places. Show at least 5 iterations in your table.

The trapezoidal channel below must supply a discharge rate of 2 x SN (m³/s). The Manning's roughness of the channel is SN/1000 (s/m) and the channel slope is SN/10000. D 2H B = 6.5 m Use MS Excel spreadsheet to set up the problem, and solve for the normal depth D to an accuracy of 4 decimal places. Show at least 5 iterations in your table.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows through a venturi as shown in the figure at a flow rate of Q=1.3L/s. The inlet and throat diameters of the venturi meter are (D = 3.0 cm andd = 2.5 cm) respectively. The height of water column in the manometers L1 and L3 are 65 and 53 cm respectively. %3D What is the experimental dynamic head at the throat-{section2} (in m)? L3
image attached.
Figure shows that the pipe flow of 50 m^3/hr, is driven by pressurized air in the tank Determine the head loss in the "smooth" pipe in meters if its friction factor is 0.014. *12.9517*99.9358*30.4889*39.5136 What gage pressure p1 in kPa, is needed to provide the given flow rate? *1121 kPa*1692 kPa*1328 kPa*1725 kPa Please answer with complete and detailed solutions. thank you. ASAP
e1
Hi, please could someone show me how U2 = 1.98m/s. This is the correct answer but i've tried a few methods and can't quite get there! Any notes on the method alongside calculation would be great :) The two pipes are parallel, Kexit =1 for pipe 1 and pipe 2, entry losses can be ignored.
Trapezoidal cross section given in the figure on the side It is requested to pass a flow rate of 5 m/s through the channel. Accepting that n=0.0167 and Jo=0.0005 in this section; size the cross section to be optimal from the hydraulic direction.
A right angled triangular notch was to measure a discharge of 0.28 m3/s from a rectangular reservoir. It was found to have an error (dH) to be 21 mm in measuring head of notch. Determine the percentage error in discharge as dQ/Q. Take Cd = 0.6
64 Q. No 2). A pipe line is designed to supplying water with flowrate of X 1/s to fulfil the demand and consumption of a city. Determine the head loss and velocity of flow in 1500 m long water supply line section having diameter of Y cm. Assuming coefficient of friction factor f=0.00155. 19.2 lowrate) and Y (Diameter) from following table
Assume the reservoir is very large in the figure below. What should be the angle (in degrees) be if each graduation corresponds to 1 lb/ft? gage pressure for PA. Answer only the numerical value in degrees. Assumptions: 1. inclined arm is fitted with 1 in apart 2. SG of fluid = 0.827 PA D = in Reservoir
Water flow passes under the sluice gate. Suppose that y₁ = 6 m and y2 = 1.9 m. (Figure 1) Figure Y₁ 4 m Y₂ 1 of 1 Part B Determine the critical depth of the flow downstream from the gate. Express your answer to three significant figures and include the appropriate units. Ye= 3.095 Submit m Previous Answers Request Answer X Incorrect; Try Again; 4 attempts remaining