The terminal voltage of a motor is 118 V, and the armature current is 38 A. If the armature resistance is 0.3 2, calculate the counter-emf. A shunt motor connected to a 120 V line draws 24 A from the line. The resistance of the field circuit is 100 N, and the armature resis- tance is 0.25 N. Calculate (a) power input to the motor; (b) power lost

The terminal voltage of a motor is 118 V, and the armature current is 38 A. If the armature resistance is 0.3 2, calculate the counter-emf. A shunt motor connected to a 120 V line draws 24 A from the line. The resistance of the field circuit is 100 N, and the armature resis- tance is 0.25 N. Calculate (a) power input to the motor; (b) power lost

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 250 V d.c. shunt motor draws 4 ampere current from mains at no load and rotates at 700 r.p.m. Find out speed of motor when input power is 8 kW. Motor armature and field resistances are 0.6 ohm and 100 ohm respectively.
The output power of a shunt motor is 7.8 hp. Its armature draws 50 A from 120 V. The armature and field winding resistances are 0.1 and 100 ohms, respectively. Find the efficiency of the motor.
answer all parts please
Q1. Calculate the current drawn by a DC Series Motor to develop the maximum power of 2000 Watt, given that the addition of armature and series field resistances is 0.5 ohm.
Please answer only handwritten accepted...I will like that solution.. Please clear handwriting.. Please.. .
The current drawn by a 220 V DC motor of armature resistance 0.5 Q and back emf 180 V is (a) 0.8 A (b) 80 A (c) 8 A (d) 18 A
3. For the simple DC motor system shown below, prove ke kt if the inductance of the winding is negligible. = Supply Vs Voltage i Armature Current VR R Back emf L VL
A 350 V shunt motor runs at it's normal speed of 720 r/min when the armature current is 90 A. The resistance of the armature is 0.3 ohm. Determine the following: (1) The kΦ1 of the motor. If armature current is 45 A and a resistance of 0.4 ohm is connected in series with the armature and the shunt field remaining constant determine the following: (2) The new kΦ2 of the motor. (3) The new speed of the motor in r/min If the current is 45 A and the shunt field is reduced to 75% of it's normal value by increasing resistance in the field circuit, determine the following: (4) The new kΦ2 of the motor. (5) The new speed of the motor in r/min
A 440 volt d.c. The armature resistance of the motor is 0.25 ohm. It takes an armature current of 60 A at 750 RPM. So find the value of torque produced in the motor.
A DC motor with permanent magnet field is running with 200 V DC supply and consuming 2 A current. A voltmeter is connected across its armature and DC supply is disconnected. The voltmeter reads 190 V just after disconnection of DC supply. Calculate the armature resistance of the machine.
1. A 230 V shunt motor takes a total current of 25 A. If the field winding resistance is 100N and the amature resistance of 0.30, Determine the Current in the armature and Back emf I need all steps , write clear please
Q1. (A)- A series DC motor runs at 600 r.p.m drawing a current of 52A when connected to 220 V supply. The total resistance of the machine is 0.14 2. Calculate the value of the external resistance to be connected in series with the motor circuit to reduce its speed to 400 r.p.m. Assume the load torque is decreased to half of the previous value. Consider the field flux is proportional to armature current.