The system shown is at rest when a constant 150-N force is applied to collar B. (a) If the force acts through the entire motion, deter- mine the speed of collar B as it strikes the support at C. (b) After what distance d should the 150-N force be removed if the collar is to reach support C with zero velocity? -600 mm 150 N 8 kg 3kg A

The system shown is at rest when a constant 150-N force is applied to collar B. (a) If the force acts through the entire motion, deter- mine the speed of collar B as it strikes the support at C. (b) After what distance d should the 150-N force be removed if the collar is to reach support C with zero velocity? -600 mm 150 N 8 kg 3kg A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The double pulley shown in the figure has a mass of 3 kg and a radius of 100 mm rotation. Knowing that when the pulley is at rest, it is applied to the cable in B, a force P of magnitude equal to 24N, determine the speed of the center of the pulley after 1.5 s and the tensile force on cable C.
3. A merry-go-round with radius R rotates in a horizontal plane at constant angular speed o. A boy with mass M at the edge begins to walk in a straight line relative to the merry-go-round from A to B with speed vo relative to the merry-go-round. Determine the magnitude of the force acting on the boy in terms of the quantities given.
2. (25) The small 2-kg block A slides down the curved path and passes the lowest point B with a speed of 4 m/s. If the radius of curvature of the path at B is 1.5 m, and the coefficient of friction between the block and path is 0.3, determine (a) the normal force exerted on the block by the path at B, and (b) the rate of change of speed at this point. B
Four pins slide in four separate slots cut in a horizontal circular plate as shown. When the plate is at rest, each pin has a velocity directed as shown and of the same constant magnitude u. Each pin has a mass m and maintains the same velocity relative to the plate when the plate rotates about O with a constant counterclockwise angular velocity w. Draw the FBDs and KDs to determine the forces on pins p1 and p2.
В (3) A smooth can C, having a mass of 3 kg, is lifted from Ö=2rad/s2 Ô = 0.5 rad/s a feed at A to a ramp at B by a rotating rod. If the rod rotates angular velocity of 0=0.5 rad/s and Ö=2rad/s?, determine the forces which the rod and 600 mm circular ramp in the vertical plane exert on the can A at the instant 0=30°. Neglect the friction and the size of the can so that r = (1.2cos0) m. The ramp -600 mm- from A to B is circular, having a radius of 600 mm.
В (3) A smooth can C, having a mass of 3 kg, is lifted from Ö=2rad/s² é = 0.5 rad/s a feed at A to a ramp at B by a rotating rod. If the rod rotates angular velocity of 0=0.5 rad/s and Ö=2rad/s2, determine the forces which the rod and 600 mm circular ramp in the vertical plane exert on the can at the instant 0=30°. Neglect the friction and the size of the can so that r = (1.2cos6) m. The ramp -600 mm- from A to B is circular, having a radius of 600 mm. m-5 kg
1) A loaded wheelbarrow is pulled to the left with an acceleration a = 2 m / s? by a force P. In this motion, the wheelbarrow does not rotate and the force of friction as well as the effect of the rotation of the wheel may be neglected. The combined mass of the wheelbarrow and its load is 250 kg with center of mass at G. For this instant, determine the horizontal and vertical components of the force P and the normal reaction at B. a P G beal 60 cm 50 cm 1 m 20 cm
IV. For the following system that starts from rest, the spool has a weight of 300 N and a radius of gyration ke = 0.3 m, and block A is attached to it as shown of weight 200 N. A constant horizontal force F is applied to the cord in order to give the block an upward speed of 5 m/s. (Neglect mass of cord and tension force). -F 1. Draw the free body diagram of the system. 2. Calculate the angular speed of the spool at t= 6 seconds. 3. Calculate the vertical reaction force at the pin at t= 6 seconds. 4. Calculate the horizontal force F.
1) A loaded wheelbarrow is pulled to the left with an acceleration a = 2 m / s2 by a force P. In this motion, the wheelbarrow does not rotate and the force of friction as well as the effect of the rotation of the wheel may be neglected. The combined mass of the wheelbarrow and its load is 250 kg with center of mass at G. For this instant, determine the horizontal and vertical components of the force P and the normal reaction at B. a P G 60 cm 50 cm 1 m 20 cm
Q4 ] Q4. The 200-kg crate rests on the ground for which the coefficients of static and kinetic friction are us = 0.3 andT respectively. The winch delivers a horizontal towing force uk = C.4 to its cable at A which varies as shown in the Fig. 4. Determine the speed of the crate when t= 4 s. Originally the tension in the cable is zero. T (N) 800 T = 400 t'/² - t (s) 4 АТ
Pr4. Two bodies are launched at the same time from two points A and B located at the same height. The distance between points A and B is d. One of the bodies starts from point A upwards with speed v1, while the other starts from point B towards point A with initial speed v2. What will be the minimal distance between the bodies during their motion? (The gravitational acceleration is g, neglect the air drag. The bodies do not reach the ground before the moment of the minimal distance.)
Given a small disk (4-Kg) sliding on top of a smooth table which is connected to an elastic cord having a tension of 8r N (r radial position of the small disk is in meters). If we gave the disk a starting velocity of 5 m/s in the transverse direction when it is at r = 1.5 m, calculate: a- the magnitudes of the radial and transverse components of its velocity when r = 3 m? b- the maximum value of r reached by the disk.